METHYL IODIDE

It is used in methylations of pharmaceuticals; in microscopy because of its high refractive index; as imbedding material for examining diatoms; and, in testing for pyridine (Budavari, 1989).
Chemical intermediate
Fumigant to control internal fungi of grain sorghum
Is used chemically as an alkylatating agent
Building block for radioactive tracer synthesis
Reacts with dimethyl ethyl amine to yield quaternary ammonium compounds.
References: (Budavari, 1989; HSDB , 1994)

FORMS

Methyl iodide is a colorless, transparent liquid; it turns brown upon exposure to light (Budavari, 1989).

SOURCES

ROUTES OF EXPOSURE - Humans are exposed to methyl iodide in ambient air since it is probably formed in the sea. Exposure would also occur from ingesting marine seafood (HSDB , 1994).

Industrial processes (see Available Forms/Sources section of this document for types)
Average Daily Air Intake (assume median conc of 3.5 parts/trillion): 0.41 microgram (HSDB , 1994)

-CLINICAL EFFECTS

GENERAL CLINICAL EFFECTS

SYSTEMIC EFFECTS: Methyl Iodide is a strong narcotic and anesthetic. Massive exposure has led to pulmonary edema. Prolonged or repeated exposure may cause central nervous system effects. The latency period between exposure and onset of symptoms ranges from hours to days.

Initial symptoms are lethargy, somnolence, slurred speech, ataxia, dysmetria, and visual disturbances. Neurologic dysfunction may progress to convulsions, coma, and death.
If recovery occurs, neurologic findings recede over several weeks and are followed by psychiatric disturbances such as paranoia, delusions, and hallucination.
In severe poisoning, the primary target organs were the lungs, liver, kidney, and brain.

SKIN: A human skin irritant which may cause burns with repeated exposure.

POTENTIAL HEALTH HAZARDS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Highly toxic, may be fatal if inhaled, swallowed or absorbed through skin.
Avoid any skin contact.
Effects of contact or inhalation may be delayed.
Fire may produce irritating, corrosive and/or toxic gases.
Runoff from fire control or dilution water may be corrosive and/or toxic and cause pollution.

-MEDICAL TREATMENT

LIFE SUPPORT

Support respiratory and cardiovascular function.

SUMMARY

FIRST AID - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Move victim to fresh air.
Call 911 or emergency medical service.
Give artificial respiration if victim is not breathing.
Do not use mouth-to-mouth method if victim ingested or inhaled the substance;give artificial respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory medical device.
Administer oxygen if breathing is difficult.
Remove and isolate contaminated clothing and shoes.
In case of contact with substance, immediately flush skin or eyes with running water for at least 20 minutes.
For minor skin contact, avoid spreading material on unaffected skin.
Keep victim warm and quiet.
Effects of exposure (inhalation, ingestion or skin contact) to substance may be delayed.
Ensure that medical personnel are aware of the material(s) involved and take precautions to protect themselves.

FIRST AID

FIRST AID

There is no specific antidote. Care is symptomatic and supportive for CNS depression and skin, eye, pulmonary, and gastrointestinal irritation. Move victim to fresh air and call emergency medical care; if not breathing, give artificial respiration; if breathing is difficult, give oxygen.
In case of contact with material, immediately flush skin or eyes with running water for at least 15 minutes.
Speed in removing material from skin is of extreme importance.
Remove and isolate contaminated clothing and shoes at the site.
Keep victim quiet and maintain normal body temperature.
Effects may be delayed; keep victim under observation.

IRRITATION

Many chemicals cause irritation of the eyes, skin, and respiratory tract. In severe cases respiratory tract irritation can progress to ARDS/acute lung injury, which may be delayed in onset for up to 24 to 72 hours in some cases.
Irritation or burns of the esophagus or gastrointestinal tract are also possible if caustic or irritant chemicals are ingested.

INHALATION EXPOSURE

INHALATION: Move patient to fresh air. Monitor for respiratory distress. If cough or difficulty breathing develops, evaluate for respiratory tract irritation, bronchitis, or pneumonitis. Administer oxygen and assist ventilation as required. Treat bronchospasm with an inhaled beta2-adrenergic agonist. Consider systemic corticosteroids in patients with significant bronchospasm.
ACUTE LUNG INJURY: Maintain ventilation and oxygenation and evaluate with frequent arterial blood gases and/or pulse oximetry monitoring. Early use of PEEP and mechanical ventilation may be needed.

DERMAL EXPOSURE -

DECONTAMINATION: Remove contaminated clothing and jewelry and irrigate exposed areas with copious amounts of water. A physician may need to examine the area if irritation or pain persists.

EYE EXPOSURE -

DECONTAMINATION: Remove contact lenses and irrigate exposed eyes with copious amounts of room temperature 0.9% saline or water for at least 15 minutes. If irritation, pain, swelling, lacrimation, or photophobia persist after 15 minutes of irrigation, the patient should be seen in a healthcare facility.

ORAL EXPOSURE -

If swallowed and victim is conscious, have victim drink water or milk. Do not induce vomiting (CHRIS , 1993).

-RANGE OF TOXICITY

MINIMUM LETHAL EXPOSURE

GENERAL/SUMMARY

The minimum lethal human dose to this agent has not been delineated.

ANIMAL DATA

HISTORICAL DATA - Single oral doses of 70 mg/kg were lethal to rabbits, but several oral doses of 50 mg/kg were necessary before they caused death (Bucknell, 1950).
HISTORICAL DATA - Inhalation of 54 ppm was fatal to mice within 24 hours (Bucknell, 1950).

MAXIMUM TOLERATED EXPOSURE

ROUTE OF EXPOSURE

A chemical worker accidently exposed to an unknown concentration of the vapor developed giddiness, diarrhea, sleepiness, and irritability, with recovery in a week. When re-exposed three months later, he experienced drowsiness, vomiting, pallor, incoordination, slurred speech, muscular twitching, oliguria, coma, and death (Hathaway et al, 1991).
Experimental application of the liquid to human skin produced a stinging sensation and slight reddening in 10 minutes. After 6 hours of contact there was spreading erythema followed by formation of vesicles (Hathaway et al, 1991).
The liquid splashed in the eyes causes conjunctivitis (Hathaway et al, 1991).

ANIMAL DATA

HISTORICAL DATA - Repeated oral doses of 30 to 50 mg/kg methyl iodide caused minimal effect in mice (Bucknell, 1950).

Carcinogenicity Ratings for CAS74-88-4 :

ACGIH (American Conference of Governmental Industrial Hygienists, 2010): Not Listed ; Listed as: Methyl iodide
EPA (U.S. Environmental Protection Agency, 2011): Not Assessed under the IRIS program. ; Listed as: Methyl iodide
IARC (International Agency for Research on Cancer (IARC), 2016; International Agency for Research on Cancer, 2015; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2010; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2010a; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2008; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2007; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2006; IARC, 2004): 3 ; Listed as: Methyl iodide

3 : The agent (mixture or exposure circumstance) is not classifiable as to its carcinogenicity to humans. This category is used most commonly for agents, mixtures and exposure circumstances for which the evidence of carcinogenicity is inadequate in humans and inadequate or limited in experimental animals. Exceptionally, agents (mixtures) for which the evidence of carcinogenicity is inadequate in humans but sufficient in experimental animals may be placed in this category when there is strong evidence that the mechanism of carcinogenicity in experimental animals does not operate in humans. Agents, mixtures and exposure circumstances that do not fall into any other group are also placed in this category.

NIOSH (National Institute for Occupational Safety and Health, 2007): Ca ; Listed as: Methyl iodide

Ca : NIOSH considers this substance to be a potential occupational carcinogen (See Appendix A in the NIOSH Pocket Guide to Chemical Hazards).

MAK (DFG, 2002): Category 2 ; Listed as: Methyl iodide

Category 2 : Substances that are considered to be carcinogenic for man because sufficient data from long-term animal studies or limited evidence from animal studies substantiated by evidence from epidemiological studies indicate that they can make a significant contribution to cancer risk. Limited data from animal studies can be supported by evidence that the substance causes cancer by a mode of action that is relevant to man and by results of in vitro tests and short-term animal studies.

NTP (U.S. Department of Health and Human Services, Public Health Service, National Toxicology Project ): Not Listed

TOXICITY AND RISK ASSESSMENT VALUES

EPA IRIS

EPA Risk Assessment Values for CAS74-88-4 (U.S. Environmental Protection Agency, 2011):

Oral:

Slope Factor:
RfD:

Inhalation:

Unit Risk:
RfC:

Drinking Water:

Unit Risk:

TOXICITY VALUES

References: Lewis, 1992 RTECS, 1993
- LC50- (INHALATION)RAT:
- LCLo- (INHALATION)MOUSE:
- LD50- (INTRAPERITONEAL)GUINEA_PIG:
- LD50- (INTRAPERITONEAL)MOUSE:
- LD50- (SUBCUTANEOUS)MOUSE:
- LD50- (INTRAPERITONEAL)RAT:
- LD50- (SUBCUTANEOUS)RAT:
- LDLo- (ORAL)RABBIT:
- LDLo- (ORAL)RAT:
- LDLo- (SKIN)RAT:
- LDLo- (SUBCUTANEOUS)RAT:
- TDLo- (INTRAPERITONEAL)MOUSE:
- TDLo- (SUBCUTANEOUS)RAT:

-STANDARDS AND LABELS

WORKPLACE STANDARDS

ACGIH TLV Values for CAS74-88-4 (American Conference of Governmental Industrial Hygienists, 2010):

Editor's Note: The listed values are recommendations or guidelines developed by ACGIH(R) to assist in the control of health hazards. They should only be used, interpreted and applied by individuals trained in industrial hygiene. Before applying these values, it is imperative to read the introduction to each section in the current TLVs(R) and BEI(R) Book and become familiar with the constraints and limitations to their use. Always consult the Documentation of the TLVs(R) and BEIs(R) before applying these recommendations and guidelines.

Adopted Value

Methyl iodide

TLV:

TLV-TWA: 2 ppm
TLV-STEL:
TLV-Ceiling:

Notations and Endnotes:

Carcinogenicity Category: Not Listed
Codes: Skin
Definitions:

Skin: This refers to the potential significant contribution to the overall exposure by the cutaneous route, including mucous membranes and the eyes, either by contact with vapors or, of likely greater significance, by direct skin contact with the substance. It should be noted that although some materials are capable of causing irritation, dermatitis, and sensitization in workers, these properties are not considered relevant when assigning a skin notation. Rather, data from acute dermal studies and repeated dose dermal studies in animals or humans, along with the ability of the chemical to be absorbed, are integrated in the decision-making toward assignment of the skin designation. Use of the skin designation provides an alert that air sampling would not be sufficient by itself in quantifying exposure from the substance and that measures to prevent significant cutaneous absorption may be warranted. Please see "Definitions and Notations" (in TLV booklet) for full definition.

TLV Basis - Critical Effect(s): Eye dam; CNS impair
Molecular Weight: 141.95

For gases and vapors, to convert the TLV from ppm to mg/m(3):

[(TLV in ppm)(gram molecular weight of substance)]/24.45

For gases and vapors, to convert the TLV from mg/m(3) to ppm:

[(TLV in mg/m(3))(24.45)]/gram molecular weight of substance

AIHA WEEL Values for CAS74-88-4 (AIHA, 2006):

Not Listed

NIOSH REL and IDLH Values for CAS74-88-4 (National Institute for Occupational Safety and Health, 2007):

Listed as: Methyl iodide
REL:

TWA: 2 ppm (10 mg/m(3))
STEL:
Ceiling:
Carcinogen Listing: (Ca) NIOSH considers this substance to be a potential occupational carcinogen (See Appendix A in the NIOSH Pocket Guide to Chemical Hazards).
Skin Designation: [skin]

Indicates the potential for dermal absorption; skin exposure should be prevented as necessary through the use of good work practices and gloves, coveralls, goggles, and other appropriate equipment.

Note(s): See Appendix A

IDLH:

IDLH: 100 ppm
Note(s): Ca

Ca: NIOSH considers this substance to be a potential occupational carcinogen (See Appendix A).

OSHA PEL Values for CAS74-88-4 (U.S. Occupational Safety, and Health Administration (OSHA), 2010):

Listed as: Methyl iodide
Table Z-1 for Methyl iodide:

8-hour TWA:

ppm: 5

Parts of vapor or gas per million parts of contaminated air by volume at 25 degrees C and 760 torr.

mg/m3: 28

Milligrams of substances per cubic meter of air. When entry is in this column only, the value is exact; when listed with a ppm entry, it is approximate.

Ceiling Value:
Skin Designation: Yes
Notation(s): Not Listed

OSHA List of Highly Hazardous Chemicals, Toxics, and Reactives for CAS74-88-4 (U.S. Occupational Safety and Health Administration, 2010):

Threshold Quantity, in pounds:7500

ENVIRONMENTAL STANDARDS

EPA CERCLA, Hazardous Substances and Reportable Quantities for CAS74-88-4 (U.S. Environmental Protection Agency, 2010):

Listed as: Methyl iodide
Final Reportable Quantity, in pounds (kilograms):

100 (45.4)

Additional Information:
Listed as: Iodomethane
Final Reportable Quantity, in pounds (kilograms):

100 (45.4)

Additional Information:
Listed as: Methane, iodo-
Final Reportable Quantity, in pounds (kilograms):

100 (45.4)

Additional Information:

EPA CERCLA, Hazardous Substances and Reportable Quantities, Radionuclides for CAS74-88-4 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA RCRA Hazardous Waste Number for CAS74-88-4 (U.S. Environmental Protection Agency, 2010b):

Listed as: Methane, iodo-
P or U series number: U138
Footnote:
Listed as: Methyl iodide
P or U series number: U138
Footnote:
Editor's Note: The D, F, and K series waste numbers and Appendix VIII to Part 261 -- Hazardous Constituents were not included. Please refer to 40 CFR Part 261.

EPA SARA Title III, Extremely Hazardous Substance List for CAS74-88-4 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA SARA Title III, Community Right-to-Know for CAS74-88-4 (40 CFR 372.65, 2006; 40 CFR 372.28, 2006):

Listed as: Methyl iodide
Effective Date for Reporting Under 40 CFR 372.30: 1/1/87
Lower Thresholds for Chemicals of Special Concern under 40 CFR 372.28:

DOT List of Marine Pollutants for CAS74-88-4 (49 CFR 172.101 - App. B, 2005):

Not Listed

EPA TSCA Inventory for CAS74-88-4 (EPA, 2005):

Listed as: Methane, iodo-

SHIPPING REGULATIONS

SURFACE

DOT -- Table of Hazardous Materials and Special Provisions for UN/NA Number 2644 (49 CFR 172.101, 2005):

Hazardous materials descriptions and proper shipping name: Methyl iodide

Symbol(s): Not Listed
Hazard class or Division: 6.1

6.1: Poisonous materials. See 49 CFR section 173.132 for definitions.

Identification Number: UN2644
Packing Group: I

I: Packing Group I - indicates the degree of danger presented by the material is great.

Label(s) required (if not excepted): 6.1

6.1: Poison Inhalation Hazard (inhalation hazard, Zone A or B) or Poison (other than inhalation hazard, Zone A or B; the packing group for a material is indicated in column 5 of the table.).

Special Provisions: 2, B9, B14, B32, B74, T20, TP2, TP13, TP38, TP45

2: This material is poisonous by inhalation (see sxn. 171.8 of this subchapter) in Hazard Zone B (see sxn. 173.116(a) or sxn. 173.133(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter.
B9: Bottom outlets are not authorized.
B14: Each bulk packaging, except a tank car or a multi-unit-tank car tank, must be insulated with an insulating material so that the overall thermal conductance at 15.5 °C (60 °F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Insulating materials must not promote corrosion to steel when wet.
B32: MC 312, MC 330, MC 331, DOT 412 cargo tanks and DOT 51 portable tanks must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of sxn. 173.24b(b) of this subchapter. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 6.35 mm (0.250 inch) or the thickness required for a tank with a design pressure at least equal to 1.3 times the vapor pressure of the lading at 46 °C (115 °F). In addition, MC 312 and DOT 412 cargo tank motor vehicles must: a. Be ASME Code (U) stamped for 100% radiography of all pressure-retaining welds; b. Have accident damage protection which conforms with sxn. 178.345-8 of this subchapter; c. Have a MAWP or design pressure of at least 87 psig; and d. Have a bolted manway cover.
B74: Tank cars must have a test pressure of 20.68 Bar (300 psig) or greater and conform to Class 105S, 106, 110, 112J, 114J or 120S.
T20: Minimum test pressure (bar): 10; Minimum shell thickness (in mm-reference steel) (See sxn.178.274(d)): 8 mm; Pressure-relief requirements (See sxn.178.275(g)): sxn. 178.275(g)(3); Bottom opening requirements (See sxn.178.275(d)): Prohibited.
TP2: a. The maximum degree of filling must not exceed the degree of filling determined by the following: [Degree of filling = 95/1+alpha(tr - tf)], where tr is the maximum mean bulk temperature during transport, tf is the temperature in degrees celsius of the liquid during filling, and alpha is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (tf) and the maximum mean bulk temperature during transportation (tr) both in degrees celsius; and b. For liquids transported under ambient conditions a may be calculated using the formula: [alpha = (d15-d50)/(35 x d50)], where d15 and d50 are the densities (in units of mass per unit volume) of the liquid at 15 degrees C (59 degrees F) and 50 degrees C (122 degrees F), respectively.
TP13: Self-contained breathing apparatus must be provided when this hazardous material is transported by sea.
TP38: Each portable tank must be insulated with an insulating material so that the overall thermal conductance at 15.5 °C (60 °F) is no more than 1.5333 kilojoules per hour per square meter per degree Celsius (0.075 Btu per hour per square foot per degree Fahrenheit) temperature differential. Insulating materials may not promote corrosion to steel when wet.
TP45: Each portable tank must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. Thickness of stainless steel for portable tank shells and heads must be the greater of 6.35 mm (0.250 inch) or the thickness required for a portable tank with a design pressure at least equal to 1.3 times the vapor pressure of the hazardous material at 46 °C (115 °F).

Packaging Authorizations (refer to 49 CFR 173.***):

Exceptions: None
Non-bulk packaging: 227
Bulk packaging: 244

Quantity Limitations:

Passenger aircraft or railcar: Forbidden
Cargo aircraft only: Forbidden

Vessel Stowage Requirements:

Vessel stowage location: A

A: The material may be stowed "on deck" or "under deck" on a cargo vessel and on a passenger vessel.

Vessel stowage other: 12, 40

12: Keep as cool as reasonably practicable.
40: Stow "clear of living quarters".

ICAO International Shipping Name for UN2644 (ICAO, 2002):

Proper Shipping Name: Methyl iodide
UN Number: 2644

LABELS

NFPA

NFPA Hazard Ratings for CAS74-88-4 (NFPA, 2002):

Not Listed

-HANDLING AND STORAGE

SUMMARY

INDUSTRIAL CHEMICALS

EMERGENCY ACTION

Keep unnecessary people away; isolate hazard area and deny entry.
Stay upwind, out of low areas, and ventilate closed spaces before entering.
Positive pressure self-contained breathing apparatus (SCBA) and chemical protective clothing which is specifically recommended by the shipper or manufacturer may be worn. It may provide little or no thermal protection.
Structural firefighters' protective clothing is NOT effective with these materials.
Remove and isolate contaminated clothing at the site.
CALL CHEMTREC AT 1-800-424-9300 AS SOON AS POSSIBLE, especially if there is no local hazardous materials team available.
Reference: DOT, 1990.

EXTENSIVE NIOSH RECOMMENED RESPIRATOR and PROTECTIVE CLOTHING SUGGESTIONS are INCLUDED in the Methyl Iodide HAZARDTEXT(R) DOCUMENT.

STORAGE

CONTAINER

Keep containers closed and store in a dark place (HSDB , 1993; Budavari, 1989).

-PERSONAL PROTECTION

SUMMARY

RECOMMENDED PROTECTIVE CLOTHING - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Wear positive pressure self-contained breathing apparatus (SCBA).
Wear chemical protective clothing that is specifically recommended by the manufacturer. It may provide little or no thermal protection.
Structural firefighters' protective clothing provides limited protection in fire situations ONLY; it is not effective in spill situations where direct contact with the substance is possible.

RESPIRATORY PROTECTION

Refer to "Recommendations for respirator selection" in the NIOSH Pocket Guide to Chemical Hazards on TOMES Plus(R) for respirator information.

PROTECTIVE CLOTHING

CHEMICAL PROTECTIVE CLOTHING. Search results for CAS 74-88-4.

All data are compiled from published sources and are NOT recommended specifically by Truven Health Analytics. The appearance of specific manufacturers or products in this section does not represent an endorsement by Truven Health Analytics. No attempt has been made to verify the data presented. All product recommendations should be confirmed with the specific manufacturer for verification of product performance.
CLOTHING

Chlorinated Polyethylene

DuPont Personal Protection

StaSafe CPE

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): Immediate
Permeation Rate (mcg/cm2/min): >100
Notes: Not Listed
Citation: (DuPont, 2002)

Standard Safety Equipment Company

ChemMaster

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): Immediate
Permeation Rate (mcg/cm2/min): >100
Notes: Not Listed
Citation: (Standard Safety Equipment, 1995)

Neoprene

River City

Neoprene splash suits

Degradation Rating: Not Recommended
Breakthrough Time (minutes): Not Listed
Permeation Rate (mcg/cm2/min): Not Listed
Notes: Not Listed
Citation: (River City, 1995)

Plastic Laminate

DuPont Personal Protection

Responder

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None detected
Notes: Not Listed
Citation: (DuPont, 2002)

Responder Plus

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None detected
Notes: Not Listed
Citation: (DuPont, 2002)

Tychem 10,000

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): <0.001
Notes: liquid
Citation: (DuPont, 2002)

Tychem 7500

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: liquid
Citation: (DuPont, 2002)

Tychem 9400

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): <0.01
Notes: liquid
Citation: (DuPont, 2002)

Tychem BR

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): <0.01
Notes: Not Listed
Citation: (DuPont, 2002)

Tychem LV

Degradation Rating: Not Listed
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): <0.01
Notes: Not Listed
Citation: (DuPont, 2003)

Tychem QC

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: liquid
Citation: (DuPont, 2002)

Tychem SL

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: liquid
Citation: (DuPont, 2002)

Tychem TK

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): <0.01
Notes: Not Listed
Citation: (DuPont, 2002)
Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): <0.01
Notes: liquid
Citation: (DuPont, 2002)

Polyvinyl Chloride

River City

PVC splash suits

Degradation Rating: Fair
Breakthrough Time (minutes): Not Listed
Permeation Rate (mcg/cm2/min): Not Listed
Notes: Not Listed
Citation: (River City, 1995)

Teflon Laminate

Mar-Mac Manufacturing, Inc.

Commander Ultrapro

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): 32
Permeation Rate (mcg/cm2/min): 24
Notes: Not Listed
Citation: (Mar-Mac Manufacturing, Inc, 1995)

FOOTWEAR

Specific recommendations and test data for this product type were not found in the available manufacturers' product literature.

GLOVES

Butyl

Best Manufacturing

Butyl 878

Degradation Rating: Not Recommended
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: Tested with Limited Exposure Method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: Tested with Limited Exposure Method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)

North Safety Products

Butyl Series

Degradation Rating: Poor
Breakthrough Time (minutes): 55
Permeation Rate (mcg/cm2/min): 82000
Notes: Not Listed
Citation: (North, 2002)
Degradation Rating: Poor
Breakthrough Time (minutes): 55
Permeation Rate (mcg/cm2/min): 82000
Notes: Not Listed
Citation: (North, 2002)

Natural Rubber

Best Manufacturing

Original Nitty Gritty

Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): 15
Permeation Rate (mcg/cm2/min): 82
Notes: Tested under limited exposure method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): 15
Permeation Rate (mcg/cm2/min): 82
Notes: Tested under limited exposure method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)

Neoprene

Best Manufacturing

Chloroflex 723

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 7
Permeation Rate (mcg/cm2/min): 116
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 7
Permeation Rate (mcg/cm2/min): 116
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)

Neoprene 6780 Series

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Tested
Permeation Rate (mcg/cm2/min): Not Tested
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)

Ultraflex Neoprene 32

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 8
Permeation Rate (mcg/cm2/min): 152
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 8
Permeation Rate (mcg/cm2/min): 152
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)

MAPA Spontex, Inc.

Chem-ply/N-440

Degradation Rating: Not Tested
Breakthrough Time (minutes): 9
Permeation Rate (mcg/cm2/min): 342
Notes: 99%
Citation: (MAPA Professional, 2004)

Neoprene+NatR

Best Manufacturing

Chem Master CHM

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 8
Permeation Rate (mcg/cm2/min): 152
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 1
Permeation Rate (mcg/cm2/min): 131
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)

Nitrile

Best Manufacturing

N-DEX 8005

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 2
Permeation Rate (mcg/cm2/min): 391
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 2
Permeation Rate (mcg/cm2/min): 391
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)

Nitri-Solve 727

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 47
Permeation Rate (mcg/cm2/min): 6
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 47
Permeation Rate (mcg/cm2/min): 6
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)

Ultimate N-Dex 9905

Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): 2
Permeation Rate (mcg/cm2/min): 391
Notes: Tested with Limited Exposure Method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): 2
Permeation Rate (mcg/cm2/min): 391
Notes: Tested with Limited Exposure Method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)

Ultraflex Nitrile 22R

Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): 6
Permeation Rate (mcg/cm2/min): 147
Notes: Tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2004)
Degradation Rating: Not Recommended (after 60 minutes of testing)
Breakthrough Time (minutes): 6
Permeation Rate (mcg/cm2/min): 147
Notes: Tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2004)

Perfect Fit Glove Co, LLC

Cobra F-466

Degradation Rating: Excellent
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None detected
Notes: 0.99
Citation: (MAPA Professional, 2003)

Nitrile+PVC

Best Manufacturing

Hustler 725R

Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 15
Permeation Rate (mcg/cm2/min): 154
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): Not Recommended
Permeation Rate (mcg/cm2/min): Not Recommended
Notes: Not Listed
Citation: (Best Manufacturing, 2002)
Degradation Rating: Not Recommended (after 60 minutes)
Breakthrough Time (minutes): 15
Permeation Rate (mcg/cm2/min): 154
Notes: tested through limited exposure method (ATSM F 1383)
Citation: (Best Manufacturing, 2002)

Plastic Laminate

North -- Safety 4H

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): 123
Permeation Rate (mcg/cm2/min): Not reported
Notes: tested at 21 degrees C; 70 degrees F
Citation: (Safety 4, 2002)
Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): 8
Permeation Rate (mcg/cm2/min): Not reported
Notes: tested at 35 degrees C; 95 degrees F
Citation: (Safety 4, 2002)

North Safety Products

Silver Shield

Degradation Rating: Poor
Breakthrough Time (minutes): 4
Permeation Rate (mcg/cm2/min): 26
Notes: Not Listed
Citation: (North, 2002)
Degradation Rating: Poor
Breakthrough Time (minutes): 4
Permeation Rate (mcg/cm2/min): 26
Notes: Not Listed
Citation: (North, 2002)

Viton

North Safety Products

Viton Series

Degradation Rating: Good
Breakthrough Time (minutes): 378
Permeation Rate (mcg/cm2/min): 700
Notes: Not Listed
Citation: (North, 2002)
Degradation Rating: Good
Breakthrough Time (minutes): 378
Permeation Rate (mcg/cm2/min): 700
Notes: Not Listed
Citation: (North, 2002)

Viton over Butyl

Best Manufacturing

Viton #890

Degradation Rating: Excellent (after 60 minutes of testing)
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None Detected
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Excellent (after 60 minutes of testing)
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None Detected
Notes: Not Listed
Citation: (Best Manufacturing, 2004)
Degradation Rating: Excellent (after 60 minutes of testing)
Breakthrough Time (minutes): >240
Permeation Rate (mcg/cm2/min): None Detected
Notes: Tested with limited exposure method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)
Degradation Rating: Excellent (after 60 minutes of testing)
Breakthrough Time (minutes): >240
Permeation Rate (mcg/cm2/min): None Detected
Notes: Tested with limited exposure method (ASTM F 1383)
Citation: (Best Manufacturing, 2004)

GENERAL INFORMATION

This section provides a compilation of chemical resistance information and test data for specific protective clothing products. Chemical resistance information includes both degradation resistance ratings and permeation resistance data. This information is designed to assist in the selection of appropriate protective clothing. Only data on specific products and manufacturers are included. Generic information or recommendations are not provided since significant differences can exist in the chemical resistance for apparent similar product types.
Specific product information is organized by general product type (gloves, garments, and footwear), material type, and manufacturer. The category 'garments' may include totally encapsulating suits, splash suits, as well as other items (e.g., coveralls, jackets, and aprons). Specific manufacturers should be contacted to determine the features of available styles/models.
In addition to chemical resistance information, there are many critical variables in the selection of protective clothing which cannot be represented in this summary of the literature. Some factors to be considered in choosing protective clothing include, but are not limited to: overall clothing integrity, physical hazard resistance, durability, human factors, ease of decontamination, and cost. Overall clothing integrity refers to a specific design's ability to offer consistent protection for all clothing-covered areas of the body. Physical hazards include resisting the effects of abrasion, cuts, tears, and punctures. Human factors entail effects on wearer mobility, visibility, and hearing for garments; dexterity, tactility, and grip for gloves; ankle support and weight for footwear; and, any effect of the clothing on the function of the wearer. There are several variations in the design for gloves, garments, and footwear that affect these factors. Protective clothing must properly be sized and correctly fit the wearer to ensure its proper use and function.
As required in the U.S.A., protective clothing should be selected based on a risk assessment of the workplace. This risk assessment must account for the identification of existing as well as potential hazards and involve the recommendation of protective clothing appropriate for the identified hazards. Therefore, the recommendations in this section should not be used as the sole basis for decisions on choice of protective clothing, but rather should be used as a tool by qualified occupational health and safety professionals or other technically qualified persons in conjunction with a review of all mitigating factors. Consult the OSHA PPE Standard (29 CFR 1910.132 - 1910.138) for regulations and additional guidance regarding the selection and use of protective clothing and equipment. For general information on protective clothing selection, refer to the "PERSONAL PROTECTIVE EQUIPMENT - OSHA PUB 3077" document.
PROTECTIVE CLOTHING SELECTION

Determine the type of protective clothing item needed based on a risk assessment (e.g., gloves, garments, footwear).
For high risk situations, choose clothing that covers all parts of the body that may be exposed. In many cases, multiple clothing items will be required. Low risk situations may permit partial body protective clothing. Select protective clothing products that have reported chemical resistance data. High risk situations involving full body clothing or extended chemical contact often require permeation resistance data to determine the barrier effectiveness of materials used in the construction of clothing. Relatively low risk situations, where only splash or incidental exposure occur, may allow use of protective clothing based on degradation or penetration resistance data. Specifics on the interpretation of chemical resistance data are presented below.
Other factors must be considered in addition to chemical resistance. The selected chemical protective clothing item should offer the optimal combination of protection against identified hazards while allowing maximum function and comfort.

INTERPRETATION OF DEGRADATION RATINGS

Degradation refers to physical changes in a material as the result of chemical exposure. Degradation may become evident in visible changes, such as discoloration, swelling, delamination, deterioration, or disintegration. Degradation effects may also be measured by weight change or other changes in a material's physical properties (e.g., strength, elasticity, hardness).
Degradation resistance ratings are provided by manufacturers to rate the amount of degradation that occurs for a particular protective clothing material when contacted by a chemical. All degradation ratings are qualitative and include ratings, such as "EXCELLENT," "GOOD," "FAIR," "POOR," and "NOT RECOMMENDED." There is no standard test method for the measurement of chemical degradation resistance; therefore, manufacturer ratings may be based on different testing approaches. This makes comparison of degradation ratings between manufacturers unreliable.
The use of degradation resistance ratings alone to recommend protective clothing, particularly for high hazard situations, should be avoided. Degradation resistance testing does not directly assess the barrier quality of protective clothing, since materials can show relatively little degradation but still allow either permeation or penetration by a chemical. Degradation resistance ratings can be used to exclude protective clothing materials from consideration. Protective clothing materials with a "NOT RECOMMENDED" degradation resistance rating should never be used.
For some products, the rating "NO PENETRATION" is provided. This refers to penetration resistance test results that are based on a different procedure (American Society for Testing and Materials (ASTM) Standard Test Method F 903). Penetration resistance testing involves placing a material sample in a test cell, exposing the exterior side of the material to a chemical, and then observing the interior side of the material for visible signs of liquid penetration. Part of the test is conducted at an elevated pressure. Test results are reported as pass (no penetration) or fail (penetration detected). Unlike degradation testing, penetration testing provides an assessment of protective clothing material barrier performance. Since penetration resistance testing examines only observable amounts of liquid penetration, permeation may still occur. The use of penetration resistance data must be restricted to liquid chemicals, and should be limited to scenarios where there is no reasonable vapor exposure hazard under the conditions of exposure.

INTERPRETATION OF PERMEATION DATA

Permeation is the process of chemical movement through a material on a molecular level. Permeation resistance refers to the ability of a material to retard or prevent chemical movement through it. Permeation may occur without any visible signs of degradation.
Permeation resistance is measured using a test cell which is divided into two halves by a protective clothing specimen. Chemical is placed on the challenge side, while the collection side is periodically monitored for permeating chemical. Permeation data were obtained in accordance with the American Society for Testing and Materials (ASTM) Standard Test Method F 739 (Resistance of Materials Used in Protective Clothing to Permeation by Liquids and Gases), unless stated otherwise. In the case of chemicals that are classified as warfare agents, the data were obtained in accordance with the Military Standard 282 (MIL-STD-282) (Military Standard, Filter Units, Protective Clothing, Gas-Mask Components, and Related Products: Performance Test Methods).
Permeation rate is the amount of chemical that passes through a material for a measured surface area per unit time. In this section, permeation rate is expressed in micrograms per square centimeter per minute (mcg/cm(2)/min). The reported permeation rate is either the steady-state rate or the maximum rate observed during testing. In some cases, very large permeation rates exceed measurement techniques and are reported as ">" (greater than) or "HIGH."
Breakthrough time is the elapsed time, in minutes, from the time the chemical comes in contact with the material exterior surface, to the time that chemical is detected on the interior surface. When no breakthrough is detected, the breakthrough time is report as ">" the testing period. If permeation breakthrough is rapid, results are reported as "<" (less than) the earlier sampling time or as "IMMEDIATELY" (which usually means breakthrough in less than 4 minutes).
The breakthrough time should exceed the expected use period of the selected protective clothing. Additionally, there are several other factors that must be taken into account to provide appropriate protection.
Permeation testing is usually conducted with full strength, undiluted chemical for the duration of the test period. Actual exposures may involve diluted chemical for short or intermittent exposure periods.
Permeation testing is usually conducted at room temperature. Permeation occurs faster at elevated temperatures (short breakthrough times and higher permeation rates) and slower at reduced temperatures (long breakthrough times and lower permeation rates).
Permeation resistance of mixtures cannot usually be determined on the basis of the individual chemicals making up the mixture. Synergistic effects may occur and result in more rapid permeation than accounted for by the individual mixture chemicals.
Permeation rates may be used to calculate potential wearer exposure; however, several assumptions must be made about the extent of exposure and condition of clothing wear. Furthermore, there are few chemicals with dermal exposure limits, making it difficult to determine an acceptable skin exposure level.

COMPANY INFORMATION

Best Manufacturing 579 Edison Street Menlo, GA 30731 USA Phone: (706) 862-2302 Fax: (706) 862-6000 Toll-Free: (800) 241-0323 Website: http://www.bestglove.com Email: USA@bestglove.com
DuPont Personal Protection P. O. Box 80705 Wilmington, DE 19880-0705 USA Phone: (302) 774-1000 Toll-Free: (800) 931-3456 Website: http://personalprotection.dupont.com Email: personalprotection@usa.dupont.com
MAPA Spontex, Inc. 100 Spontex Dr. Columbia, TN 38401 USA Phone: (800) 537--2897 Fax: (800) 537--3299 Website: http://www.mapaglove.com Email: sales@mapaglove.com
Mar-Mac Manufacturing, Inc. P. O. Box P.O. Box 278 McBee, SC 29101 USA Phone: (843) 335-8211 Fax: (843) 355-8599 Toll-Free: (843) 335-8211 Website: http://www.marmac.com Email: info@marmac.com
North -- Safety 4H 2000 Plainfield Pike Cranston, RI 02921 USA Phone: (800) 430-4110 Fax: (800) 572-6346 Toll-Free: (800) 430-4110 Website: http://www.safety4.com
North Safety Products 2000 Plainfield Pike Cranston, RI 02921 USA Phone: (800) 430-4110 Fax: (800) 572-6346 Toll-Free: (800) 430-4110 Website: http://www.northsafety.com Email: marketing@northsafety.com
Perfect Fit Glove Co, LLC 85 Innsbruck Dr. Buffalo, NY 14227 USA Phone: (800) 245-6837 Fax: (716) 668-3224 Toll-Free: (800) 245-6837 Website: http://www.perfectfitglove.com Email: perfectfitglove@perfectfitglove.com
River City 5321 East Shelby Dr. Memphis, TN 38188 USA Phone: (800) 888-0347 Fax: (901) 795-3815 Toll-Free: (800) 888-0347 Website: http://www.protectivewear.com Email: support@protectivewear.com
Standard Safety Equipment Company 1407 Ridgeview Drive McHenry, IL 60050 USA Phone: (815) 363-8565 Fax: (815) 363-8633 Toll-Free: (815) 363-8565 Website: http://www.standardsafety.com Email: solson@standardsafety.com

REFERENCES

CHEMICAL PROTECTIVE CLOTHING CITATIONS

The following sources were consulted for chemical protective clothing data:

(Ansell-Edmont, 2001)
(Bata Shoe Company, 1995)
(Best Manufacturing, 2002)
(Best Manufacturing, 2004)
(Boss Manufacturing Company, 1998)
(ChemFab Corporation, 1993)
(Comasec Safety, Inc., 2003)
(Comasec Safety, Inc., 2003a)
(DuPont, 2002)
(DuPont, 2002)
(DuPont, 2003)
(Guardian Manufacturing Group, 2001)
(ILC Dover, Inc., 1998)
(Kappler Inc., 2001)
(Kimberly-Clark, 2002)
(LaCrosse-Rainfair, 1997)
(MAPA Professional, 2003)
(MAPA Professional, 2004)
(Mar-Mac Manufacturing, Inc, 1995)
(Marigold Industrial, 2003)
(Memphis Glove Company, 2001)
(Montgomery Safety Products, 1995)
(Nat-Wear, 2001)
(Neese Industries, Inc., 2003)
(North, 2002)
(North, 2002)
(Playtex, 1995)
(River City, 1995)
(Safety 4, 2002)
(Servus, 1995)
(Standard Safety Equipment, 1995)
(Tingley, 2002)
(Trelleborg-Viking, Inc., 2001)
(Trelleborg-Viking, Inc., 2002)
(Wells Lamont Industrial, 2002)
(Workrite, 1997)

-PHYSICAL HAZARDS

FIRE HAZARD

SUMMARY

POTENTIAL FIRE OR EXPLOSION HAZARDS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)
- Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes.
- Containers may explode when heated.
- Runoff may pollute waterways.
Methyl iodide is nonflammable by standard tests in air (Clayton & Clayton, 1981).

FLAMMABILITY CLASSIFICATION

NFPA Flammability Rating for CAS74-88-4 (NFPA, 2002):

Not Listed

FIRE CONTROL/EXTINGUISHING AGENTS

SMALL FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Dry chemical, CO2 or water spray.

LARGE FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Water spray, fog or regular foam.
Move containers from fire area if you can do it without risk.
Dike fire control water for later disposal; do not scatter the material.
Use water spray or fog; do not use straight streams.

TANK OR CAR/TRAILER LOAD FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Fight fire from maximum distance or use unmanned hose holders or monitor nozzles.
Do not get water inside containers.
Cool containers with flooding quantities of water until well after fire is out.
Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank.
ALWAYS stay away from tanks engulfed in fire.
For massive fire, use unmanned hose holders or monitor nozzles; if this is impossible, withdraw from area and let fire burn.

NFPA Extinguishing Methods for CAS74-88-4 (NFPA, 2002):

Not Listed

COMBUSTION TOXICITY

When heated to decomposition, methyl iodide emits toxic fumes of iodine (Lewis, 1992).

EXPLOSION HAZARD

Methyl iodide forms an explosive reaction with trialkylphosphines and with silver chlorite (Lewis, 1992).

DUST/VAPOR HAZARD

The vapor is moderately irritating such that a person cannot usually tolerate moderate or high vapor concentrations (CHRIS , 1993).

REACTIVITY HAZARD

Methyl iodide is incompatible with strong oxidizers (HSDB , 1993).

It forms a violent reaction with oxygen at 300 to 500 degrees C and with sodium (even in solution) (Lewis, 1992).

Methyl iodide forms an explosive reaction with trialkylphosphines and with silver chlorite (Lewis, 1992).

When heated to decomposition, methyl iodide emits toxic fumes of iodine (Lewis, 1992).

EVACUATION PROCEDURES

SUMMARY

Initial Isolation and Protective Action Distances (ERG, 2004)

Data presented from the Emergency Response Guidebook Table of Initial Isolation and Protective Action Distances are for use when a spill has occurred and there is no fire. If there is a fire, or if a fire is involved, evacuation information presented under FIRE - PUBLIC SAFETY EVACUATION DISTANCES should be used.
Generally, a small spill is one that involves a single, small package such as a drum containing up to approximately 200 liters, a small cylinder, or a small leak from a large package. A large spill is one that involves a spill from a large package, or multiple spills from many small packages.
Suggested distances to protect from vapors of toxic-by-inhalation and/or water-reactive materials during the first 30 minutes following the spill.

DOT ID No. 2644 - Methyl iodide

SMALL SPILLS

First isolate in all directions: 30 meters (100 feet).
Note wind direction.
Then protect persons downwind:

during the DAY for: 0.1 kilometers (0.1 miles); or
during the NIGHT for: 0.2 kilometers (0.1 miles).

LARGE SPILLS

First isolate in all directions: 30 meters (100 feet).
Note wind direction.
Then protect persons downwind:

during the DAY for: 0.3 kilometers (0.2 miles); or
during the NIGHT for: 0.8 kilometers (0.5 miles).

SPILL - PUBLIC SAFETY EVACUATION DISTANCES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

Increase, in the downwind direction, as necessary, the isolation distance of at least 25 to 50 meters (80 to 160 feet) in all directions.

FIRE - PUBLIC SAFETY EVACUATION DISTANCES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions.

PUBLIC SAFETY MEASURES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)

CALL Emergency Response Telephone Number on Shipping Paper first. If Shipping Paper not available or no answer, refer to appropriate telephone number:

MEXICO:

SETIQ:

01-800-00-214-00 in the Mexican Republic;
For calls originating in Mexico City and the Metropolitan Area: 5559-1588;
For calls originating elsewhere, call: 011-52-555-559-1588.

CENACOM:

01-800-00-413-00 in the Mexican Republic;
For calls originating in Mexico City and the Metropolitan Area: 5550-1496, 5550-1552, 5550-1485, or 5550-4885;
For calls originating elsewhere, call: 011-52-555-550-1496, or 011-52-555-550-1552; 011-52-555-550-1485, or 011-52-555-550-4885.

ARGENTINA:

CIQUIME:

0-800-222-2933 in the Republic of Argentina;
For calls originating elsewhere, call: +54-11-4613-1100.

BRAZIL:

PRÓ-QUÍMICA:

0-800-118270 (Toll-free in Brazil);
For calls originating elsewhere, call: +55-11-232-1144 (Collect calls are accepted).

COLUMBIA:

CISPROQUIM:

01-800-091-6012 in Colombia;
For calls originating in Bogotá, Colombia, call: 288-6012;
For calls originating elsewhere, call: 011-57-1-288-6012.

CANADA:

CANUTEC:

613-996-6666 (Collect calls are accepted);
*666 cellular (in Canada only).

UNITED STATES:

CHEMTREC®:

1-800-424-9300 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
703-527-3887 for calls originating elsewhere (Collect calls are accepted).

CHEM-TEL, INC.:

1-800-255-3924 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
813-248-0585 for calls originating elsewhere (Collect calls are accepted).

INFOTRAC:

1-800-535-5053 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
352-323-3500 for calls originating elsewhere (Collect calls are accepted).

3E COMPANY:

1-800-451-8346 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
760-602-8703 for calls originating elsewhere (Collect calls are accepted).

NATIONAL RESPONSE CENTER (NRC):

1-800-424-8802 - (24 hours) (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
202-267-2675 for calls in the District of Columbia.

MILITARY SHIPMENTS:

703-697-0218 - Explosives/ammunition incidents (Collect calls are accepted);
1-800-851-8061 - All other dangerous goods incidents.

NATIONWIDE POISON CONTROL CENTER (United States only):

1-800-222-1222 (Toll-free in the U.S.).

For additional details see the section entitled "WHO TO CALL FOR ASSISTANCE" under the ERG Instructions.
As an immediate precautionary measure, isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
Keep unauthorized personnel away.
Stay upwind.
Keep out of low areas.

AIHA ERPG Values for CAS74-88-4 (AIHA, 2006):

Listed as Methyl Iodide
ERPG-1 (units = ppm): 25
ERPG-2 (units = ppm): 50
ERPG-3 (units = ppm): 125
Under Ballot, Review, or Consideration: No
Definitions:

ERPG-1: The ERPG-1 is the maximum airborne concentration below which it is believed nearly all individuals could be exposed for up to one hour without experiencing more than mild, transient adverse health effects or perceiving a clearly defined objectionable odor.
ERPG-2: The ERPG-2 is the maximum airborne concentration below which it is believed nearly all individuals could be exposed for up to one hour without experiencing or developing irreversible or other serious health effects or symptoms that could impair an individual's ability to take protective action.
ERPG-3: The ERPG-3 is the maximum airborne concentration below which it is believed nearly all individuals could be exposed for up to one hour without experiencing or developing life-threatening health effects.

DOE TEEL Values for CAS74-88-4 (U.S. Department of Energy, Office of Emergency Management, 2010):

Listed as Methyl iodide
TEEL-0 (units = ppm): 5
TEEL-1 (units = ppm): 25
TEEL-2 (units = ppm): 50
TEEL-3 (units = ppm): 125
Definitions:

TEEL-0: The threshold concentration below which most people will experience no adverse health effects.
TEEL-1: The airborne concentration (expressed as ppm [parts per million] or mg/m(3) [milligrams per cubic meter]) of a substance above which it is predicted that the general population, including susceptible individuals, could experience notable discomfort, irritation, or certain asymptomatic, nonsensory effects. However, these effects are not disabling and are transient and reversible upon cessation of exposure.
TEEL-2: The airborne concentration (expressed as ppm or mg/m(3)) of a substance above which it is predicted that the general population, including susceptible individuals, could experience irreversible or other serious, long-lasting, adverse health effects or an impaired ability to escape.
TEEL-3: The airborne concentration (expressed as ppm or mg/m(3)) of a substance above which it is predicted that the general population, including susceptible individuals, could experience life-threatening adverse health effects or death.

AEGL Values for CAS74-88-4 (National Research Council, 2010; National Research Council, 2009; National Research Council, 2008; National Research Council, 2007; NRC, 2001; NRC, 2002; NRC, 2003; NRC, 2004; NRC, 2004; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; United States Environmental Protection Agency Office of Pollution Prevention and Toxics, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; 62 FR 58840, 1997; 65 FR 14186, 2000; 65 FR 39264, 2000; 65 FR 77866, 2000; 66 FR 21940, 2001; 67 FR 7164, 2002; 68 FR 42710, 2003; 69 FR 54144, 2004):

Listed as: Methyl Iodide
Proposed Value:

AEGL-1

10 min exposure:

ppm: 54 ppm
mg/m3: 310 mg/m(3)

30 min exposure:

ppm: 31 ppm
mg/m3: 180 mg/m(3)

1 hr exposure:

ppm: 22 ppm
mg/m3: 130 mg/m(3)

4 hr exposure:

ppm: 11 ppm
mg/m3: 64 mg/m(3)

8 hr exposure:

ppm: 11 ppm
mg/m3: 64 mg/m(3)

Definitions:

AEGL-1 is the airborne concentration of a substance above which it is predicted that the general population, including susceptible individuals, could experience notable discomfort, irritation, or certain asymptomatic non-sensory effects. However, the effects are not disabling, are transient, and are reversible upon cessation of exposure.

Listed as: Methyl Iodide
Proposed Value:

AEGL-2

10 min exposure:

ppm: 200 ppm
mg/m3: 1200 mg/m(3)

30 min exposure:

ppm: 120 ppm
mg/m3: 700 mg/m(3)

1 hr exposure:

ppm: 82 ppm
mg/m3: 480 mg/m(3)

4 hr exposure:

ppm: 41 ppm
mg/m3: 240 mg/m(3)

8 hr exposure:

ppm: 29 ppm
mg/m3: 170 mg/m(3)

Definitions:

AEGL-2 is the airborne concentration of a substance above which it is predicted that the general population, including susceptible individuals, could experience irreversible or other serious, long-lasting adverse health effects or an impaired ability to escape.

Listed as: Methyl Iodide
Proposed Value:

AEGL-3

10 min exposure:

ppm: 670 ppm
mg/m3: 3900 mg/m(3)

30 min exposure:

ppm: 400 ppm
mg/m3: 2300 mg/m(3)

1 hr exposure:

ppm: 290 ppm
mg/m3: 1700 mg/m(3)

4 hr exposure:

ppm: 150 ppm
mg/m3: 870 mg/m(3)

8 hr exposure:

ppm: 98 ppm
mg/m3: 570 mg/m(3)

Definitions:

AEGL-3 is the airborne concentration of a substance above which it is predicted that the general population, including susceptible individuals, could experience life-threatening health effects or death.

NIOSH IDLH Values for CAS74-88-4 (National Institute for Occupational Safety and Health, 2007):

IDLH: 100 ppm
Note(s): Ca

(Ca) NIOSH considers this substance to be a potential occupational carcinogen (See Appendix A).

CONTAINMENT/WASTE TREATMENT OPTIONS

SUMMARY

SPILL OR LEAK PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)
- Do not touch damaged containers or spilled material unless wearing appropriate protective clothing.
- Stop leak if you can do it without risk.
- Prevent entry into waterways, sewers, basements or confined areas.
- Cover with plastic sheet to prevent spreading.
- Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers.
- DO NOT GET WATER INSIDE CONTAINERS.
RECOMMENDED PROTECTIVE CLOTHING - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 151 (ERG, 2004)
- Wear positive pressure self-contained breathing apparatus (SCBA).
- Wear chemical protective clothing that is specifically recommended by the manufacturer. It may provide little or no thermal protection.
- Structural firefighters' protective clothing provides limited protection in fire situations ONLY; it is not effective in spill situations where direct contact with the substance is possible.
At the time of this review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices (HSDB , 1993).
Methyl iodide is a potential candidate for liquid injection incineration, rotary kiln incineration, and fluidized bed incineration (HSDB , 1993).

-ENVIRONMENTAL HAZARD MANAGEMENT

POLLUTION HAZARD

Methyl iodide is produced by many marine photosynthetic organisms, therefore, the ocean is thought to be a major natural source of methyl iodide (HSDB , 1993).

AIR: Methyl iodide photolyzes in air with a half-life of 7 hours and less under smog conditions (HSDB , 1993).

WATER: Methyl iodide will be removed from the water by volatilization (half-life 3.6 hours in a typical river). In the ocean, methyl iodide will react with chloride to form methyl chloride (methyl iodide half-life 20 and 58 days at 19.2 and 10.8 degrees C, respectively). In placid bodies of fresh water, hydrolysis of methyl iodide may be significant (half-life 100 to 251 days). Photolysis may also be important but there are no data with which to evaluate its extent. It will not be expected to bind to sediments or to bioconcentrate in aquatic organisms; however, there is some evidence of bioaccumulation in marine animals (HSDB , 1993).

SOIL: If spilled on land, methyl iodide would be expected to volatilize rapidly. It will not be expected to sorb to soils. No studies could be found concerning its fate on land but it could photolyze or decompose by reacting with chlorides (HSDB , 1993).

ENVIRONMENTAL FATE AND KINETICS

OTHER

OTHER
- AIR: The half-life of methyl iodide in air via removal by photolysis is 7 hours (less under smog conditions) (HSDB , 1993).
- WATER: The half-life of methyl iodide in typical river water via removal by volatilization is 3.6 hours. In the ocean, the half-life of methyl iodide via reaction with chloride to form methyl chloride is 20 days at 19.2 degrees C and 58 days 10.8 degrees C. In placid bodies of fresh water, hydrolysis of methyl iodide may be significant, with a half-life 100 to 251 days (HSDB , 1993).

ENVIRONMENTAL TOXICITY

WATER: Methyl iodide is not harmful to aquatic life (CHRIS , 1993).

-PHYSICAL/CHEMICAL PROPERTIES

MOLECULAR WEIGHT

141.95 (Budavari, 1989)

DESCRIPTION/PHYSICAL STATE

Methyl iodide is a colorless, transparent liquid; it turns brown upon exposure to light (Budavari, 1989).

ODOR: Has been described as pungent, sweet, or ethereal (HSDB , 1994).

VAPOR PRESSURE

400 mmHg (at 25.3 degrees C) (Lewis, 1992)

SPECIFIC GRAVITY

TEMPERATURE AND/OR PRESSURE NOT LISTED

2.28 (Budavari, 1989)

DENSITY

OTHER TEMPERATURE AND/OR PRESSURE

2.28 g/cm(3) (at 20/4 degrees C) (Budavari, 1989)

FREEZING/MELTING POINT

MELTING POINT

-66.5 degrees C (Budavari, 1989)

BOILING POINT

42.5 degrees C (decomposes at 270 degrees C) (Budavari, 1989)

SOLUBILITY

IN WATER

Methyl iodide is soluble in about 50 parts water (Budavari, 1989).
Solubility in water is 14 g/L at 20 deg C (HSDB , 1994).
Sinks and decomposes in water, forming a poisonous vapor cloud (CHRIS , 1994).

IN ORGANIC SOLVENTS

ALCOHOL: Miscible/Soluble (Budavari, 1989; HSDB , 1994)
ETHER: Miscible (Budavari, 1989)
BENZENE: Soluble (HSDB , 1994)
CHLOROFORM: Soluble (HSDB , 1994)
CARBON TETRACHLORIDE: Soluble (HSDB , 1994)

-REFERENCES

GENERAL BIBLIOGRAPHY

40 CFR 372.28: Environmental Protection Agency - Toxic Chemical Release Reporting, Community Right-To-Know, Lower thresholds for chemicals of special concern. National Archives and Records Administration (NARA) and the Government Printing Office (GPO). Washington, DC. Final rules current as of Apr 3, 2006.

40 CFR 372.65: Environmental Protection Agency - Toxic Chemical Release Reporting, Community Right-To-Know, Chemicals and Chemical Categories to which this part applies. National Archives and Records Association (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Apr 3, 2006.

49 CFR 172.101 - App. B: Department of Transportation - Table of Hazardous Materials, Appendix B: List of Marine Pollutants. National Archives and Records Administration (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Aug 29, 2005.

49 CFR 172.101: Department of Transportation - Table of Hazardous Materials. National Archives and Records Administration (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Aug 11, 2005.

62 FR 58840: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 1997.

65 FR 14186: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

65 FR 39264: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

65 FR 77866: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

66 FR 21940: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2001.

67 FR 7164: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2002.

68 FR 42710: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2003.

69 FR 54144: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2004.

AIHA: 2006 Emergency Response Planning Guidelines and Workplace Environmental Exposure Level Guides Handbook, American Industrial Hygiene Association, Fairfax, VA, 2006.

AMA Department of DrugsAMA Department of Drugs: AMA Evaluations Subscription, American Medical Association, Chicago, IL, 1992.

American Conference of Governmental Industrial Hygienists : ACGIH 2010 Threshold Limit Values (TLVs(R)) for Chemical Substances and Physical Agents and Biological Exposure Indices (BEIs(R)), American Conference of Governmental Industrial Hygienists, Cincinnati, OH, 2010.

Anon: Current Intelligence Bulletin 43 - Monohalomethanes. Methyl chloride CH3Cl, methyl bromide CH3Br, methyl iodide CH3I. DHHS (NIOSH) Publication No 84-117, NIOSH, US Department of Health and Human Services, Cincinnati, OH, 1984.

Ansell-Edmont: SpecWare Chemical Application and Recommendation Guide. Ansell-Edmont. Coshocton, OH. 2001. Available from URL: http://www.ansellpro.com/specware. As accessed 10/31/2001.

Appel GB, Galen J, & O'Brien: Methyl iodide intoxication. Ann Intern Med 1975; 82:534-536.

Artigas A, Bernard GR, Carlet J, et al: The American-European consensus conference on ARDS, part 2: ventilatory, pharmacologic, supportive therapy, study design strategies, and issues related to recovery and remodeling.. Am J Respir Crit Care Med 1998; 157:1332-1347.

Aw TC & Boyland E: IRCS Med Sci Libr Compend 1981; 9:29-30.

Azuara-Blanco A, Pillai CT, & Dua HS: Amniotic membrane transplantation for ocular surface reconstruction. Br J Ophthalmol 1999; 83:399-402.

Barnsley EA & Young L: Biochemical studies of toxic agents. The metabolism of iodomethane. Biochem J 1965; 95:77-81.

Baselga-Monte MS, Estadella-Botha S, & Quer-Brossa S: Occupational methyl iodide intoxication (Spanish). Medicina del Lavoro 1965; 56:592-595.

Bata Shoe Company: Industrial Footwear Catalog, Bata Shoe Company, Belcamp, MD, 1995.

Best Manufacturing: ChemRest Chemical Resistance Guide. Best Manufacturing. Menlo, GA. 2002. Available from URL: http://www.chemrest.com. As accessed 10/8/2002.

Best Manufacturing: Degradation and Permeation Data. Best Manufacturing. Menlo, GA. 2004. Available from URL: http://www.chemrest.com/DomesticPrep2/. As accessed 04/09/2004.

Bonnefoi MS, Davenport CJ, & Morgan KT: Metabolism and toxicity of methyl iodide in primary dissociated neural cell cultures. Neurotoxicology 1991; 12:33-46.

Bonnefoi MS: Mitochondrial glutathione and methyl iodide-induced neurotoxicity in primary neural cell cultures. Neurotoxicology 1992; 13:401-412.

Boss Manufacturing Company: Work Gloves, Boss Manufacturing Company, Kewanee, IL, 1998.

Brodovsky SC, McCarty AC, & Snibson G: Management of alkali burns an 11-year retrospective review. Ophthalmology 2000; 107:1829-1835.

Brodovsky SC, McCarty CA, & Snibson G: Management of alkali burns an 11-year retrospective review. Ophthalmology 2000a; 107:1829-1835.

Brodovsky SC, McCarty CA, & Snibson G: Management of alkali burns an 11-year review. Ophthalmology 2000b; 107:1829-1835.

Brophy GM, Bell R, Claassen J, et al: Guidelines for the evaluation and management of status epilepticus. Neurocrit Care 2012; 17(1):3-23.

Brower RG, Matthay AM, & Morris A: Ventilation with lower tidal volumes as compared with traditional tidal volumes for acute lung injury and the acute respiratory distress syndrome. N Eng J Med 2000; 342:1301-1308.

Bucknell M: The toxicity of methyl iodide: Preliminary survey. Br J Ind Med 1950; 7:122-124.

Budavari S: The Merck Index, 11th ed, Merck & Co, Inc, Rahway, NJ, 1989, pp 957.

Burgess JL, Kirk M, Borron SW, et al: Emergency department hazardous materials protocol for contaminated patients. Ann Emerg Med 1999; 34(2):205-212.

CHRIS : CHRIS Hazardous Chemical Data. US Department of Transportation, US Coast Guard. Washington, DC (Internet Version). Edition expires 1993; provided by Truven Health Analytics Inc., Greenwood Village, CO.

CHRIS : CHRIS Hazardous Chemical Data. US Department of Transportation, US Coast Guard. Washington, DC (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Caravati EM, Knight HH, & Linscott MS: Esophageal laceration and charcoal mediastinum complicating gastric lavage. J Emerg Med 2001; 20:273-276.

Caravati EM: Alkali. In: Dart RC, ed. Medical Toxicology, Lippincott Williams & Wilkins, Philadelphia, PA, 2004.

Carvajal HF & Stewart CE: Emergency management of burn patients: the first few hours. Emerg Med Reports 1987; 8:129-136.

Cataletto M: Respiratory Distress Syndrome, Acute(ARDS). In: Domino FJ, ed. The 5-Minute Clinical Consult 2012, 20th ed. Lippincott Williams & Wilkins, Philadelphia, PA, 2012.

Chamberlain JM, Altieri MA, & Futterman C: A prospective, randomized study comparing intramuscular midazolam with intravenous diazepam for the treatment of seizures in children. Ped Emerg Care 1997; 13:92-94.

ChemFab Corporation: Chemical Permeation Guide Challenge Protective Clothing Fabrics, ChemFab Corporation, Merrimack, NH, 1993.

Chin RF , Neville BG , Peckham C , et al: Treatment of community-onset, childhood convulsive status epilepticus: a prospective, population-based study. Lancet Neurol 2008; 7(8):696-703.

Choonara IA & Rane A: Therapeutic drug monitoring of anticonvulsants state of the art. Clin Pharmacokinet 1990; 18:318-328.

Chyka PA, Seger D, Krenzelok EP, et al: Position paper: Single-dose activated charcoal. Clin Toxicol (Phila) 2005; 43(2):61-87.

Clayton GD & Clayton FE: Patty's Industrial Hygiene and Toxicology, Toxicology, 3rd ed, 2B, John Wiley & Sons, New York, NY, 1982.

Comasec Safety, Inc.: Chemical Resistance to Permeation Chart. Comasec Safety, Inc.. Enfield, CT. 2003. Available from URL: http://www.comasec.com/webcomasec/english/catalogue/mtabgb.html. As accessed 4/28/2003.

Comasec Safety, Inc.: Product Literature, Comasec Safety, Inc., Enfield, CT, 2003a.

DFG: List of MAK and BAT Values 2002, Report No. 38, Deutsche Forschungsgemeinschaft, Commission for the Investigation of Health Hazards of Chemical Compounds in the Work Area, Wiley-VCH, Weinheim, Federal Republic of Germany, 2002.

Di Simplicio P, Dolara P, & Lodovici M: Blood glutathione as a measure of exposure to toxic compounds. J Appl Toxicol 1984; 4:227-229.

DuPont: DuPont Suit Smart: Interactive Tool for the Selection of Protective Apparel. DuPont. Wilmington, DE. 2002. Available from URL: http://personalprotection.dupont.com/protectiveapparel/suitsmart/smartsuit2/na_english.asp. As accessed 10/31/2002.

DuPont: Permeation Guide for DuPont Tychem Protective Fabrics. DuPont. Wilmington, DE. 2003. Available from URL: http://personalprotection.dupont.com/en/pdf/tyvektychem/pgcomplete20030128.pdf. As accessed 4/26/2004.

DuPont: Permeation Test Results. DuPont. Wilmington, DE. 2002a. Available from URL: http://www.tyvekprotectiveapprl.com/databases/default.htm. As accessed 7/31/2002.

EPA: Search results for Toxic Substances Control Act (TSCA) Inventory Chemicals. US Environmental Protection Agency, Substance Registry System, U.S. EPA's Office of Pollution Prevention and Toxics. Washington, DC. 2005. Available from URL: http://www.epa.gov/srs/.

ERG: Emergency Response Guidebook. A Guidebook for First Responders During the Initial Phase of a Dangerous Goods/Hazardous Materials Incident, U.S. Department of Transportation, Research and Special Programs Administration, Washington, DC, 2004.

Ehler E, Latta J, Eichlerova A, et al: Exposure to iodomethane and dichloromethane associated with a confusional state. Neurotoxicology 2011; 32(3):307-311.

Elliot CG, Colby TV, & Kelly TM: Charcoal lung. Bronchiolitis obliterans after aspiration of activated charcoal. Chest 1989; 96:672-674.

Ernst AA, Thomson T, & Haynes ML: Warmed versus room temperature saline solution for ocular irrigation: a randomized clinical trial. Ann Emerg Med 1998; 32:676-679.

FDA: Poison treatment drug product for over-the-counter human use; tentative final monograph. FDA: Fed Register 1985; 50:2244-2262.

Fish R & Davidson RS: Management of ocular thermal and chemical injuries, including amniotic membrane therapy. Curr Opin Ophthalmol 2010; 21(4):317-321.

Gandy J, Millner GC, & Bates HK: Effects of selected chemicals on the glutathione status in the male reproductive system of rats. J Toxicol Environ Health 1990; 29:45-57.

Gansewendt B, Xu D, & Foest U: DNA binding of methyl iodide in male and female F344 rats. Carcinogenesis 1991; 12:463-467.

Golej J, Boigner H, Burda G, et al: Severe respiratory failure following charcoal application in a toddler. Resuscitation 2001; 49:315-318.

Graff GR, Stark J, & Berkenbosch JW: Chronic lung disease after activated charcoal aspiration. Pediatrics 2002; 109:959-961.

Grant WM & Schuman JS: Toxicology of the Eye, 4th ed, Charles C Thomas, Springfield, IL, 1993.

Grant WM & Schuman JS: Toxicology of the Eye, 4th ed, Charles C Thomas, Springfield, IL, 1993a.

Grant WM: Toxicology of the Eye, 3rd ed, Charles C Thomas, Springfield, IL, 1986.

Guardian Manufacturing Group: Guardian Gloves Test Results. Guardian Manufacturing Group. Willard, OH. 2001. Available from URL: http://www.guardian-mfg.com/guardianmfg.html. As accessed 12/11/2001.

HSDB : Hazardous Substances Data Bank. National Library of Medicine. Bethesda, MD (Internet Version). Edition expires 1993; provided by Truven Health Analytics Inc., Greenwood Village, CO.

HSDB : Hazardous Substances Data Bank. National Library of Medicine. Bethesda, MD (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Haas CF: Mechanical ventilation with lung protective strategies: what works?. Crit Care Clin 2011; 27(3):469-486.

Harris CR & Filandrinos D: Accidental administration of activated charcoal into the lung: aspiration by proxy. Ann Emerg Med 1993; 22:1470-1473.

Hasegawa H, Hung Yang J, & Sata M: Experimental study of methyl iodide poisoning. Industr Health 1967; 6:119-134.

Hasegawa H, Sato M, & Suzuki H: Experimental study of methyl iodide poisoning. II. Industr Health 1971; 9:36-45.

Hathaway GJ, Proctor NH, & Hughes JP: Chemical Hazards of the Workplace, 3rd ed, Van Nostrand Reinhold Company, New York, NY, 1991, pp 401-402.

Haynes BW Jr: Emergency department management of minor burns. Top Emerg Med 1981; 3:35-40.

Hegenbarth MA & American Academy of Pediatrics Committee on Drugs: Preparing for pediatric emergencies: drugs to consider. Pediatrics 2008; 121(2):433-443.

Hvidberg EF & Dam M: Clinical pharmacokinetics of anticonvulsants. Clin Pharmacokinet 1976; 1:161.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: 1,3-Butadiene, Ethylene Oxide and Vinyl Halides (Vinyl Fluoride, Vinyl Chloride and Vinyl Bromide), 97, International Agency for Research on Cancer, Lyon, France, 2008.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Formaldehyde, 2-Butoxyethanol and 1-tert-Butoxypropan-2-ol, 88, International Agency for Research on Cancer, Lyon, France, 2006.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Household Use of Solid Fuels and High-temperature Frying, 95, International Agency for Research on Cancer, Lyon, France, 2010a.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Smokeless Tobacco and Some Tobacco-specific N-Nitrosamines, 89, International Agency for Research on Cancer, Lyon, France, 2007.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Some Non-heterocyclic Polycyclic Aromatic Hydrocarbons and Some Related Exposures, 92, International Agency for Research on Cancer, Lyon, France, 2010.

IARC: List of all agents, mixtures and exposures evaluated to date - IARC Monographs: Overall Evaluations of Carcinogenicity to Humans, Volumes 1-88, 1972-PRESENT. World Health Organization, International Agency for Research on Cancer. Lyon, FranceAvailable from URL: http://monographs.iarc.fr/monoeval/crthall.html. As accessed Oct 07, 2004.

IARC: Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Man. 1972-PRESENT, 15, International Agency for Research on Cancer, World Health Organization, Geneva, Switzerland, 1977, pp p251.

IARC: Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Man. 1972-PRESENT. (Multivolume work), International Agency for Research on Cancer, World Health Organization, Geneva, Switzerland, 1987, pp pS766.

ICAO: Technical Instructions for the Safe Transport of Dangerous Goods by Air, 2003-2004. International Civil Aviation Organization, Montreal, Quebec, Canada, 2002.

ILC Dover, Inc.: Ready 1 The Chemturion Limited Use Chemical Protective Suit, ILC Dover, Inc., Frederica, DE, 1998.

International Agency for Research on Cancer (IARC): IARC monographs on the evaluation of carcinogenic risks to humans: list of classifications, volumes 1-116. International Agency for Research on Cancer (IARC). Lyon, France. 2016. Available from URL: http://monographs.iarc.fr/ENG/Classification/latest_classif.php. As accessed 2016-08-24.

International Agency for Research on Cancer: IARC Monographs on the Evaluation of Carcinogenic Risks to Humans. World Health Organization. Geneva, Switzerland. 2015. Available from URL: http://monographs.iarc.fr/ENG/Classification/. As accessed 2015-08-06.

Johnson MK: Metabolism of iodomethane in the rat. Biochem J 1966; 98:38-43.

Kappler, Inc.: Suit Smart. Kappler, Inc.. Guntersville, AL. 2001. Available from URL: http://www.kappler.com/suitsmart/smartsuit2/na_english.asp?select=1. As accessed 7/10/2001.

Kimberly-Clark, Inc.: Chemical Test Results. Kimberly-Clark, Inc.. Atlanta, GA. 2002. Available from URL: http://www.kc-safety.com/tech_cres.html. As accessed 10/4/2002.

Kollef MH & Schuster DP: The acute respiratory distress syndrome. N Engl J Med 1995; 332:27-37.

Kuckelkorn R, Kottek A, & Schrage N: Poor prognosis of severe chemical and thermal eye burns: the need for adequate emergency care and primary prevention. Int Arch Occup Environ Health 1995; 281-284.

LaCrosse-Rainfair: Safety Products, LaCrosse-Rainfair, Racine, WI, 1997.

Leaver SK & Evans TW: Acute respiratory distress syndrome. BMJ 2007; 335(7616):389-394.

Lewis RJ: Sax's Dangerous Properties of Industrial Materials, 8th ed, Van Nostrand Reinhold Company, New York, NY, 1992, pp 2333.

Loddenkemper T & Goodkin HP: Treatment of Pediatric Status Epilepticus. Curr Treat Options Neurol 2011; Epub:Epub.

MAPA Professional: Chemical Resistance Guide. MAPA North America. Columbia, TN. 2003. Available from URL: http://www.mapaglove.com/pro/ChemicalSearch.asp. As accessed 4/21/2003.

MAPA Professional: Chemical Resistance Guide. MAPA North America. Columbia, TN. 2004. Available from URL: http://www.mapaglove.com/ProductSearch.cfm?id=1. As accessed 6/10/2004.

Mackison FW, Stricoff RS, & Partidge LJ Jr: NIOSH/OSHA - Occupational Health Guidelines for Chemical Hazards, DHHS (NIOSH) Publication No 81-123(3 VOLS), US Government Printing Office, Washington, DC, 1981.

Manno EM: New management strategies in the treatment of status epilepticus. Mayo Clin Proc 2003; 78(4):508-518.

Mar-Mac Manufacturing, Inc: Product Literature, Protective Apparel, Mar-Mac Manufacturing, Inc., McBee, SC, 1995.

Marigold Industrial: US Chemical Resistance Chart, on-line version. Marigold Industrial. Norcross, GA. 2003. Available from URL: www.marigoldindustrial.com/charts/uschart/uschart.html. As accessed 4/14/2003.

Matsui H, Wada O, & Manabe S: Pathogenesis of hyperlipidemia induced in rabbits by methyl iodide. Toxicol Appl Pharmacol 1982; 65:245-249.

Meller D, Pires RT, & Mack RJS: Amniotic membrane transplantation for acute chemical or thermal burns. Ophthalmology 2000; 107:980-990.

Memphis Glove Company: Permeation Guide. Memphis Glove Company. Memphis, TN. 2001. Available from URL: http://www.memphisglove.com/permeation.html. As accessed 7/2/2001.

Miazek-Kula M: Determination of methyl iodide concentrations in air by gas chromatographyhrony (Polish). Prace Centralnego Instytutu Ochrony Pracy 1986; 36:127-136.

Montgomery Safety Products: Montgomery Safety Products Chemical Resistant Glove Guide, Montgomery Safety Products, Canton, OH, 1995.

Morgan A, Morgan DJ, & Evans JC: Studies on the retention and metabolism of inhaled methyl iodide - II. Metabolism of methyl iodide. Health Physics 1967; 13:1067-1074.

Morgan DJ & Morgan A: Studies on the retention and metabolism of inhaled methyl iodide -- I. retention of inhaled methyl iodide. Health Physics 1967; 13:1055-1065.

Morgan S & Murray A: Limbal autotransplantation in the acute and chronic phases of severe chemical injuries. Eye 1996; 10:349-354.

Moylan JA: Burn care after thermal injury. Top Emerg Med 1980; 2:39-52.

NFPA: Fire Protection Guide to Hazardous Materials, 13th ed., National Fire Protection Association, Quincy, MA, 2002.

NHLBI ARDS Network: Mechanical ventilation protocol summary. Massachusetts General Hospital. Boston, MA. 2008. Available from URL: http://www.ardsnet.org/system/files/6mlcardsmall_2008update_final_JULY2008.pdf. As accessed 2013-08-07.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 1, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2001.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 2, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2002.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 3, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2003.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 4, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2004.

Nair JR & Chatterjee K: Methyl iodide poisoning presenting as a mimic of acute stroke: a case report. J Med Case Reports 2010; 4(1):177.

Naradzay J & Barish RA: Approach to ophthalmologic emergencies. Med Clin North Am 2006; 90(2):305-328.

Nat-Wear: Protective Clothing, Hazards Chart. Nat-Wear. Miora, NY. 2001. Available from URL: http://www.natwear.com/hazchart1.htm. As accessed 7/12/2001.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2,3-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2,4-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2-Butylene Oxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648083cdbb&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2-Dibromoethane (Proposed). United States Environmental Protection Agency. Washington, DC. 2007g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064802796db&disposition=attachment&contentType=pdf. As accessed 2010-08-18.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,3,5-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 2-Ethylhexyl Chloroformate (Proposed). United States Environmental Protection Agency. Washington, DC. 2007b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648037904e&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Acrylonitrile (Proposed). United States Environmental Protection Agency. Washington, DC. 2007c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648028e6a3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Adamsite (Proposed). United States Environmental Protection Agency. Washington, DC. 2007h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Agent BZ (3-quinuclidinyl benzilate) (Proposed). United States Environmental Protection Agency. Washington, DC. 2007f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ad507&disposition=attachment&contentType=pdf. As accessed 2010-08-18.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Allyl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648039d9ee&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Aluminum Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Arsenic Trioxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2007m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480220305&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Automotive Gasoline Unleaded (Proposed). United States Environmental Protection Agency. Washington, DC. 2009a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cc17&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Biphenyl (Proposed). United States Environmental Protection Agency. Washington, DC. 2005j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064801ea1b7&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bis-Chloromethyl Ether (BCME) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006n. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648022db11&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Boron Tribromide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ae1d3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bromine Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2007d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648039732a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bromoacetone (Proposed). United States Environmental Protection Agency. Washington, DC. 2008e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809187bf&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Calcium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Carbonyl Fluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ae328&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Carbonyl Sulfide (Proposed). United States Environmental Protection Agency. Washington, DC. 2007e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648037ff26&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Chlorobenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2008c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803a52bb&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Cyanogen (Proposed). United States Environmental Protection Agency. Washington, DC. 2008f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809187fe&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Dimethyl Phosphite (Proposed). United States Environmental Protection Agency. Washington, DC. 2009. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbf3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Diphenylchloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648091884e&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyl Phosphorodichloridate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480920347&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2008g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809203e7&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Germane (Proposed). United States Environmental Protection Agency. Washington, DC. 2008j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963906&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Hexafluoropropylene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064801ea1f5&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ketene (Proposed). United States Environmental Protection Agency. Washington, DC. 2007. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ee7c&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Magnesium Aluminum Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Magnesium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Malathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2009k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809639df&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Mercury Vapor (Proposed). United States Environmental Protection Agency. Washington, DC. 2009b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a8a087&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl Isothiocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963a03&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl Parathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2008l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963a57&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl tertiary-butyl ether (Proposed). United States Environmental Protection Agency. Washington, DC. 2007a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064802a4985&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methylchlorosilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2005. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5f4&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyldichlorosilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2005a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c646&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN1 CAS Reg. No. 538-07-8) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN2 CAS Reg. No. 51-75-2) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN3 CAS Reg. No. 555-77-1) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Tetroxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008n. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648091855b&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Trifluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963e0c&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Parathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2008o. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963e32&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Perchloryl Fluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e268&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Perfluoroisobutylene (Proposed). United States Environmental Protection Agency. Washington, DC. 2009d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e26a&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008p. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096dd58&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyl Mercaptan (Proposed). United States Environmental Protection Agency. Washington, DC. 2006d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020cc0c&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phorate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008q. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096dcc8&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phosgene (Draft-Revised). United States Environmental Protection Agency. Washington, DC. 2009e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a8a08a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phosgene Oxime (Proposed). United States Environmental Protection Agency. Washington, DC. 2009f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e26d&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Potassium Cyanide (Proposed). United States Environmental Protection Agency. Washington, DC. 2009g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbb9&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Potassium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Propargyl Alcohol (Proposed). United States Environmental Protection Agency. Washington, DC. 2006e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec91&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Selenium Hexafluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2006f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec55&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Silane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d523&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sodium Cyanide (Proposed). United States Environmental Protection Agency. Washington, DC. 2009h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbb9&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sodium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Strontium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sulfuryl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2006h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec7a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tear Gas (Proposed). United States Environmental Protection Agency. Washington, DC. 2008s. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e551&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tellurium Hexafluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e2a1&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tert-Octyl Mercaptan (Proposed). United States Environmental Protection Agency. Washington, DC. 2008r. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e5c7&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tetramethoxysilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d632&disposition=attachment&contentType=pdf. As accessed 2010-08-17.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethoxysilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d632&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethyl Phosphite (Proposed). United States Environmental Protection Agency. Washington, DC. 2009j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7d608&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethylacetyl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008t. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e5cc&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Zinc Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for n-Butyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064808f9591&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Heart,Lung,and Blood Institute: Expert panel report 3: guidelines for the diagnosis and management of asthma. National Heart,Lung,and Blood Institute. Bethesda, MD. 2007. Available from URL: http://www.nhlbi.nih.gov/guidelines/asthma/asthgdln.pdf.

National Institute for Occupational Safety and Health: NIOSH Pocket Guide to Chemical Hazards, U.S. Department of Health and Human Services, Centers for Disease Control and Prevention, Cincinnati, OH, 2007.

National Research Council : Acute exposure guideline levels for selected airborne chemicals, 5, National Academies Press, Washington, DC, 2007.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 6, National Academies Press, Washington, DC, 2008.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 7, National Academies Press, Washington, DC, 2009.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 8, National Academies Press, Washington, DC, 2010.

Neese Industries, Inc.: Fabric Properties Rating Chart. Neese Industries, Inc.. Gonzales, LA. 2003. Available from URL: http://www.neeseind.com/new/TechGroup.asp?Group=Fabric+Properties&Family=Technical. As accessed 4/15/2003.

None Listed: Position paper: cathartics. J Toxicol Clin Toxicol 2004; 42(3):243-253.

North: Chemical Resistance Comparison Chart - Protective Footwear . North Safety. Cranston, RI. 2002. Available from URL: http://www.linkpath.com/index2gisufrm.php?t=N-USA1. As accessed April 30, 2004.

North: eZ Guide Interactive Software. North Safety. Cranston, RI. 2002a. Available from URL: http://www.northsafety.com/feature1.htm. As accessed 8/31/2002.

Peate WF: Work-related eye injuries and illnesses. Am Fam Physician 2007; 75(7):1017-1022.

Perry HD, Hodes LW, & Seedor JA: Effect of doxycycline hyclate on corneal epithelial wound healing in the rabbit alkali-burn model. Preliminary observations. Cornea 1993; 12:379-82.

Playtex: Fits Tough Jobs Like a Glove, Playtex, Westport, CT, 1995.

Pollack MM, Dunbar BS, & Holbrook PR: Aspiration of activated charcoal and gastric contents. Ann Emerg Med 1981; 10:528-529.

Product Information: diazepam IM, IV injection, diazepam IM, IV injection. Hospira, Inc (per Manufacturer), Lake Forest, IL, 2008.

Product Information: lorazepam IM, IV injection, lorazepam IM, IV injection. Akorn, Inc, Lake Forest, IL, 2008.

RTECS : Registry of Toxic Effects of Chemical Substances. National Institute for Occupational Safety and Health. Cincinnati, OH (Internet Version). Edition expires 1993; provided by Truven Health Analytics Inc., Greenwood Village, CO.

RTECS : Registry of Toxic Effects of Chemical Substances. National Institute for Occupational Safety and Health. Cincinnati, OH (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Rau NR, Nagaraj MV, Prakash PS, et al: Fatal pulmonary aspiration of oral activated charcoal. Br Med J 1988; 297:918-919.

Refsvik T: The influence of some thiols on biliary excretion of methyl mercury. Acta Pharmacol Toxicol 1983; 53:153-158.

River City: Protective Wear Product Literature, River City, Memphis, TN, 1995.

Roberts JR: Minor burns (Pt II). Emerg Med Ambulatory Care News 1988; 10:4-5.

Robertz-Vaupel GM, Bierl-R, & von Unruh G: Intravenous methyl iodide poisoning--detoxification using hemoperfusion (German). Anasthesiol-Intensivmed-Notfallmed-Schmerzther 1991; 26:44-47.

Ronk JF, Ruiz-Esmenjaud S, & Osorio M: Limbal conjunctival autograft in subacute alkaline corneal burn. Cornea 1994; 13:465-468.

Saari KM, Leinonen J, & Aine E: Management of chemical eye injuries with prolonged irrigation. Acta Ophthalmol Suppl 1984; 52-59.

Safety 4: North Safety Products: Chemical Protection Guide. North Safety. Cranston, RI. 2002. Available from URL: http://www.safety4.com/guide/set_guide.htm. As accessed 8/14/2002.

Schwartz MD, Obamwonyi AO, Thomas JD, et al: Acute methyl iodide exposure with delayed neuropsychiatric sequelae: report of a case. Am J Ind Med 2005; 47:550-556.

Scott R, Besag FMC, & Neville BGR: Buccal midazolam and rectal diazepam for treatment of prolonged seizures in childhood and adolescence: a randomized trial. Lancet 1999; 353:623-626.

Seedor JA, Perry HD, & McNamara TF: Systemic tetracycline treatment of alkali-induced corneal ulceration in rabbits. Arch Ophthalmol 1987; 105:268-271.

Servus: Norcross Safety Products, Servus Rubber, Servus, Rock Island, IL, 1995.

Singh P, Tyagi M, Kumar Y, et al: Ocular chemical injuries and their management. Oman J Ophthalmol 2013; 6(2):83-86.

Skutilova J: Acute impairment due to methyl iodide (Czech). Pracovni Lekarstvi 1975; 27:341-342.

Smilkstein MJ & Fraunfelder F: Ophthalmic Principles, In: Goldfrank LR, Flomenbaum NE, Lewin NA, et al, eds. Goldfrank's Toxicologic Emergencies. 7th ed., McGraw-Hill, New York, NY, 2002.

Spector J & Fernandez WG: Chemical, thermal, and biological ocular exposures. Emerg Med Clin North Am 2008; 26(1):125-136.

Sreenath TG, Gupta P, Sharma KK, et al: Lorazepam versus diazepam-phenytoin combination in the treatment of convulsive status epilepticus in children: A randomized controlled trial. Eur J Paediatr Neurol 2009; Epub:Epub.

Sridhar MS, Bansal AK, & Sangwan VS: Amniotic membrans transplantation in acute chemical and thermal injury. Am J Ophthalmol 2000; 130:134-137.

Standard Safety Equipment: Product Literature, Standard Safety Equipment, McHenry, IL, 1995.

Stolbach A & Hoffman RS: Respiratory Principles. In: Nelson LS, Hoffman RS, Lewin NA, et al, eds. Goldfrank's Toxicologic Emergencies, 9th ed. McGraw Hill Medical, New York, NY, 2011.

Su CY & Lin CP: Combined use of an amniotic membrane and tissue adhesive in treating corneal perforation: a case report. Ophtalmic Sufr Lasers 2000; 31:151-154.

Tingley: Chemical Degradation for Footwear and Clothing. Tingley. South Plainfield, NJ. 2002. Available from URL: http://www.tingleyrubber.com/tingley/Guide_ChemDeg.pdf. As accessed 10/16/2002.

Trelleborg-Viking, Inc.: Chemical and Biological Tests (database). Trelleborg-Viking, Inc.. Portsmouth, NH. 2002. Available from URL: http://www.trelleborg.com/protective/. As accessed 10/18/2002.

Trelleborg-Viking, Inc.: Trellchem Chemical Protective Suits, Interactive manual & Chemical Database. Trelleborg-Viking, Inc.. Portsmouth, NH. 2001.

Tuft SJ & Shortt AJ: Surgical rehabilitation following severe ocular burns. Eye (Lond) 2009; 23(10):1966-1971.

U.S. Department of Energy, Office of Emergency Management: Protective Action Criteria (PAC) with AEGLs, ERPGs, & TEELs: Rev. 26 for chemicals of concern. U.S. Department of Energy, Office of Emergency Management. Washington, DC. 2010. Available from URL: http://www.hss.doe.gov/HealthSafety/WSHP/Chem_Safety/teel.html. As accessed 2011-06-27.

U.S. Department of Health and Human Services, Public Health Service, National Toxicology Project : 11th Report on Carcinogens. U.S. Department of Health and Human Services, Public Health Service, National Toxicology Program. Washington, DC. 2005. Available from URL: http://ntp.niehs.nih.gov/INDEXA5E1.HTM?objectid=32BA9724-F1F6-975E-7FCE50709CB4C932. As accessed 2011-06-27.

U.S. Environmental Protection Agency: Discarded commercial chemical products, off-specification species, container residues, and spill residues thereof. Environmental Protection Agency's (EPA) Resource Conservation and Recovery Act (RCRA); List of hazardous substances and reportable quantities 2010b; 40CFR(261.33, e-f):77-.

U.S. Environmental Protection Agency: Integrated Risk Information System (IRIS). U.S. Environmental Protection Agency. Washington, DC. 2011. Available from URL: http://cfpub.epa.gov/ncea/iris/index.cfm?fuseaction=iris.showSubstanceList&list_type=date. As accessed 2011-06-21.

U.S. Environmental Protection Agency: List of Radionuclides. U.S. Environmental Protection Agency. Washington, DC. 2010a. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-sec302-4.pdf. As accessed 2011-06-17.

U.S. Environmental Protection Agency: List of hazardous substances and reportable quantities. U.S. Environmental Protection Agency. Washington, DC. 2010. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-sec302-4.pdf. As accessed 2011-06-17.

U.S. Environmental Protection Agency: The list of extremely hazardous substances and their threshold planning quantities (CAS Number Order). U.S. Environmental Protection Agency. Washington, DC. 2010c. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-part355.pdf. As accessed 2011-06-17.

U.S. Occupational Safety and Health Administration: Part 1910 - Occupational safety and health standards (continued) Occupational Safety, and Health Administration's (OSHA) list of highly hazardous chemicals, toxics and reactives. Subpart Z - toxic and hazardous substances. CFR 2010 2010; Vol6(SEC1910):7-.

U.S. Occupational Safety, and Health Administration (OSHA): Process safety management of highly hazardous chemicals. 29 CFR 2010 2010; 29(1910.119):348-.

USEPA/OTS: Investigation of Selected Potential Environmental Contaminants: Monohalomethanes. EPA 560/2-77-007 as cited in USEPA; Ambient Water Quality Criteria Doc: Halomethanes p C-30. EPA 442/5-80-051, Environmental Protection Agency, Washington, DC, 1977.

USEPA: Ambient Water Quality Criteria Doc: Halomethanes p, Environmental Protection Agency, Washington, DC, 1980.

United States Environmental Protection Agency Office of Pollution Prevention and Toxics: Acute Exposure Guideline Levels (AEGLs) for Vinyl Acetate (Proposed). United States Environmental Protection Agency. Washington, DC. 2006. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6af&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

Vale JA, Kulig K, American Academy of Clinical Toxicology, et al: Position paper: Gastric lavage. J Toxicol Clin Toxicol 2004; 42:933-943.

Vale JA: Position Statement: gastric lavage. American Academy of Clinical Toxicology; European Association of Poisons Centres and Clinical Toxicologists. J Toxicol Clin Toxicol 1997; 35:711-719.

Vaughan P, Lindahl T, & Sedgwick B: Induction of the adaptive response of Escherichia coli to alkylation damage by the environmental mutagen, methyl chloride. Mutat-Res 1993; 293:249-57.

Wells Lamont Industrial: Chemical Resistant Glove Application Chart. Wells Lamont Industrial. Morton Grove, IL. 2002. Available from URL: http://www.wellslamontindustry.com. As accessed 10/31/2002.

Willson DF, Truwit JD, Conaway MR, et al: The adult calfactant in acute respiratory distress syndrome (CARDS) trial. Chest 2015; 148(2):356-364.

Wilson DF, Thomas NJ, Markovitz BP, et al: Effect of exogenous surfactant (calfactant) in pediatric acute lung injury. A randomized controlled trial. JAMA 2005; 293:470-476.

Workrite: Chemical Splash Protection Garments, Technical Data and Application Guide, W.L. Gore Material Chemical Resistance Guide, Workrite, Oxnard, CA, 1997.

FeedBack

METHYL IODIDE

Classification | Information to evaluate chemical incidents

Information to evaluate chemical incidents

Information to evaluate chemical incidents

Information to evaluate chemical incidents