MALEIC ANHYDRIDE

It is used: in Diels-Alder syntheses (as a dienophile); in co-polymerization reactions; in manufacture of alkyd-type of resins; as dye intermediates; in pharmaceuticals; in agricultural chemicals (maleic hydrazide, Malathion); as a pesticide; in fumaric and tartaric acid manufacture; as preservative for oils and fats; in manufacture of polyester resins; and, in permanent press fabrics (ACGIH, 1986; Budavari, 1989; Lewis, 1992; Sax & Lewis, 1987).

FORMS

Maleic anhydride has been described as: fused black or white crystals; colorless needles; and, orthorhombic needles from chloroform, also readily by sublimation (ACGIH, 1986; Budavari, 1989; Lewis, 1992; Sax & Lewis, 1987).
Commercial grades are furnished in fused form, as briquettes (Budavari, 1989).

-CLINICAL EFFECTS

GENERAL CLINICAL EFFECTS

INHALATION may produce coughing, nausea, nervousness, respiratory difficulties, cardiovascular system disorders, nosebleed, headache, sneezing, throat irritation.

Workers exposed to vapors from heated maleic anhydride developed an intense burning sensation in the eyes and throat, with cough and vomiting.
Pulmonary edema may develop.

DERMAL - Skin contact causes irritation, and redness.

EYE - Vapors cause severe eye irritation and conjunctivitis, photophobia, and double vision, temporary visual impairment.

Exposure to high fume concentrations caused photophobia, double vision, and a visual phenomenon of seeing rings around lights.

POTENTIAL HEALTH HAZARDS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

TOXIC; inhalation, ingestion or contact (skin, eyes) with vapors, dusts or substance may cause severe injury, burns or death.
Contact with molten substance may cause severe burns to skin and eyes.
Reaction with water or moist air will release toxic, corrosive or flammable gases.
Reaction with water may generate much heat that will increase the concentration of fumes in the air.
Fire will produce irritating, corrosive and/or toxic gases.
Runoff from fire control or dilution water may be corrosive and/or toxic and cause pollution.

-MEDICAL TREATMENT

LIFE SUPPORT

Support respiratory and cardiovascular function.

SUMMARY

FIRST AID - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

Move victim to fresh air.
Call 911 or emergency medical service.
Give artificial respiration if victim is not breathing.
Do not use mouth-to-mouth method if victim ingested or inhaled the substance; give artificial respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory medical device.
Administer oxygen if breathing is difficult.
Remove and isolate contaminated clothing and shoes.
In case of contact with substance, immediately flush skin or eyes with running water for at least 20 minutes.
For minor skin contact, avoid spreading material on unaffected skin.
Keep victim warm and quiet.
Effects of exposure (inhalation, ingestion or skin contact) to substance may be delayed.
Ensure that medical personnel are aware of the material(s) involved and take precautions to protect themselves.

FIRST AID

INHALATION EXPOSURE -

INHALATION: Move patient to fresh air. Monitor for respiratory distress. If cough or difficulty breathing develops, evaluate for respiratory tract irritation, bronchitis, or pneumonitis. Administer oxygen and assist ventilation as required. Treat bronchospasm with an inhaled beta2-adrenergic agonist. Consider systemic corticosteroids in patients with significant bronchospasm.

DERMAL EXPOSURE -

DECONTAMINATION: Remove contaminated clothing and jewelry and irrigate exposed areas with copious amounts of water. A physician may need to examine the area if irritation or pain persists.

EYE EXPOSURE -

DECONTAMINATION: Remove contact lenses and irrigate exposed eyes with copious amounts of room temperature 0.9% saline or water for at least 15 minutes. If irritation, pain, swelling, lacrimation, or photophobia persist after 15 minutes of irrigation, the patient should be seen in a healthcare facility.

-RANGE OF TOXICITY

MINIMUM LETHAL EXPOSURE

GENERAL/SUMMARY

The minimum lethal human dose to this agent has not been delineated.

MAXIMUM TOLERATED EXPOSURE

ROUTE OF EXPOSURE

Exposure of humans to a concentration of 1.5 to 2 ppm resulted in nasal irritation within 1 minute and eye irritation after 15 to 20 minutes (Hathaway et al, 1991).
Among workers repeatedly exposed to 1.25 to 2.5 ppm, effects were ulceration of nasal mucous membranes, chronic bronchitis, and, in some cases, asthma (Hathaway et al, 1991).
Levels of 2.5 ppm and higher are extremely irritating (ACGIH, 1986).
Workers exposed to vapors from heated maleic anhydride developed an intense burning sensation in the eyes and the throat, with cough and vomiting. Exposure to high fume concentrations caused photophobia, double vision, and a visual phenomenon of seeing rings around lights (Hathaway et al, 1991).

ANIMAL DATA

An inhalation study of rats, hamsters, and monkeys exposed to 1.1, 3.3, or 9.8 mg/m(3), 6 hours/day, 5 days/week for 6 months, revealed dose-related signs of nasal and ocular irritations including discharge, sneezing, gasping, and coughing for all species (Hathaway et al, 1991).

Carcinogenicity Ratings for CAS108-31-6 :

ACGIH (American Conference of Governmental Industrial Hygienists, 2010): A4 ; Listed as: Maleic anhydride

A4 :Not Classifiable as a Human Carcinogen: Agents which cause concern that they could be carcinogenic for humans but which cannot be assessed conclusively because of a lack of data. In vitro or animal studies do not provide indications of carcinogenicity which are sufficient to classify the agent into one of the other categories.

ACGIH (American Conference of Governmental Industrial Hygienists, 2010): A4 ; Listed as: Maleic anhydride

A4 :Not Classifiable as a Human Carcinogen: Agents which cause concern that they could be carcinogenic for humans but which cannot be assessed conclusively because of a lack of data. In vitro or animal studies do not provide indications of carcinogenicity which are sufficient to classify the agent into one of the other categories.

EPA (U.S. Environmental Protection Agency, 2011): Not Assessed under the IRIS program. ; Listed as: Maleic anhydride
IARC (International Agency for Research on Cancer (IARC), 2016; International Agency for Research on Cancer, 2015; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2010; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2010a; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2008; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2007; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2006; IARC, 2004): Not Listed
NIOSH (National Institute for Occupational Safety and Health, 2007): Not Listed ; Listed as: Maleic anhydride
MAK (DFG, 2002): Not Listed
NTP (U.S. Department of Health and Human Services, Public Health Service, National Toxicology Project ): Not Listed

TOXICITY AND RISK ASSESSMENT VALUES

EPA IRIS

EPA Risk Assessment Values for CAS108-31-6 (U.S. Environmental Protection Agency, 2011):

Oral:

Slope Factor:
RfD: 1x10(-1) mg/kg-day

Inhalation:

Unit Risk:
RfC:

Drinking Water:

Unit Risk:

TOXICITY VALUES

References: Lewis, 1992 RTECS, 1993
- LD50- (ORAL)GUINEA_PIG:
- LD50- (ORAL)MOUSE:
- LD50- (ORAL)RABBIT:
- LD50- (SKIN)RABBIT:
- LD50- (INTRAPERITONEAL)RAT:
- LD50- (ORAL)RAT:
- TDLo- (ORAL)RAT:
- TDLo- (SUBCUTANEOUS)RAT:

-STANDARDS AND LABELS

WORKPLACE STANDARDS

ACGIH TLV Values for CAS108-31-6 (American Conference of Governmental Industrial Hygienists, 2010):

Editor's Note: The listed values are recommendations or guidelines developed by ACGIH(R) to assist in the control of health hazards. They should only be used, interpreted and applied by individuals trained in industrial hygiene. Before applying these values, it is imperative to read the introduction to each section in the current TLVs(R) and BEI(R) Book and become familiar with the constraints and limitations to their use. Always consult the Documentation of the TLVs(R) and BEIs(R) before applying these recommendations and guidelines.

Adopted Value

Maleic anhydride

TLV:

TLV-TWA: (0.1 ppm)
TLV-STEL:
TLV-Ceiling:

Notations and Endnotes:

Carcinogenicity Category: A4
Codes: SEN
Definitions:

A4: Not Classifiable as a Human Carcinogen: Agents which cause concern that they could be carcinogenic for humans but which cannot be assessed conclusively because of a lack of data. In vitro or animal studies do not provide indications of carcinogenicity which are sufficient to classify the agent into one of the other categories.
SEN: The designation SEN refers to the potential for an agent to produce sensitization, as confirmed by human or animal data. The notation does not imply that this is the critical effect or that this is the sole basis for the TLV. Although, for those TLVs that are based on sensitization, the TLV is meant to protect workers from induction of this effect, but cannot protect workers who have already become sensitized. The notation should be used to assist in identifying sensitization hazards and reducing respiratory, dermal, and conjunctival exposures to sensitizing agents in the workplace. Please see "Definitions and Notations" (in TLV booklet) for full definition.

TLV Basis - Critical Effect(s): (Eye, URT, and skin irr)
Molecular Weight: 98.06

For gases and vapors, to convert the TLV from ppm to mg/m(3):

[(TLV in ppm)(gram molecular weight of substance)]/24.45

For gases and vapors, to convert the TLV from mg/m(3) to ppm:

[(TLV in mg/m(3))(24.45)]/gram molecular weight of substance

Additional information:

See Notice of Intended Changes; Adopted values enclosed in parentheses are those for which changes are proposed in the Notice of Intended Changes.

Notice of Intended Changes

Maleic anhydride

TLV:

TLV-TWA: 0.01 mg/m(3)
TLV-STEL:
TLV-Ceiling:

Notations and Endnotes:

Carcinogenicity Category: A4
Codes: IFV, SEN
Definitions:

A4: Not Classifiable as a Human Carcinogen: Agents which cause concern that they could be carcinogenic for humans but which cannot be assessed conclusively because of a lack of data. In vitro or animal studies do not provide indications of carcinogenicity which are sufficient to classify the agent into one of the other categories.
IFV: Inhalable fraction and vapor.
SEN: The designation SEN refers to the potential for an agent to produce sensitization, as confirmed by human or animal data. The notation does not imply that this is the critical effect or that this is the sole basis for the TLV. Although, for those TLVs that are based on sensitization, the TLV is meant to protect workers from induction of this effect, but cannot protect workers who have already become sensitized. The notation should be used to assist in identifying sensitization hazards and reducing respiratory, dermal, and conjunctival exposures to sensitizing agents in the workplace. Please see "Definitions and Notations" (in TLV booklet) for full definition.

TLV Basis - Critical Effect(s): Resp sens
Molecular Weight: 98.06

For gases and vapors, to convert the TLV from ppm to mg/m(3):

[(TLV in ppm)(gram molecular weight of substance)]/24.45

For gases and vapors, to convert the TLV from mg/m(3) to ppm:

[(TLV in mg/m(3))(24.45)]/gram molecular weight of substance

AIHA WEEL Values for CAS108-31-6 (AIHA, 2006):

Not Listed

NIOSH REL and IDLH Values for CAS108-31-6 (National Institute for Occupational Safety and Health, 2007):

Listed as: Maleic anhydride
REL:

TWA: 1 mg/m(3) (0.25 ppm)
STEL:
Ceiling:
Carcinogen Listing: (Not Listed) Not Listed
Skin Designation: Not Listed
Note(s):

IDLH:

IDLH: 10 mg/m3
Note(s): Not Listed

OSHA PEL Values for CAS108-31-6 (U.S. Occupational Safety, and Health Administration (OSHA), 2010):

Listed as: Maleic anhydride
Table Z-1 for Maleic anhydride:

8-hour TWA:

ppm: 0.25

Parts of vapor or gas per million parts of contaminated air by volume at 25 degrees C and 760 torr.

mg/m3: 1

Milligrams of substances per cubic meter of air. When entry is in this column only, the value is exact; when listed with a ppm entry, it is approximate.

Ceiling Value:
Skin Designation: No
Notation(s): Not Listed

OSHA List of Highly Hazardous Chemicals, Toxics, and Reactives for CAS108-31-6 (U.S. Occupational Safety and Health Administration, 2010):

Not Listed

ENVIRONMENTAL STANDARDS

EPA CERCLA, Hazardous Substances and Reportable Quantities for CAS108-31-6 (U.S. Environmental Protection Agency, 2010):

Listed as: 2,5-Furandione
Final Reportable Quantity, in pounds (kilograms):

5000 (2270)

Additional Information:
Listed as: Maleic anhydride
Final Reportable Quantity, in pounds (kilograms):

5000 (2270)

Additional Information:

EPA CERCLA, Hazardous Substances and Reportable Quantities, Radionuclides for CAS108-31-6 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA RCRA Hazardous Waste Number for CAS108-31-6 (U.S. Environmental Protection Agency, 2010b):

Listed as: 2,5-Furandione
P or U series number: U147
Footnote:
Listed as: Maleic anhydride
P or U series number: U147
Footnote:
Editor's Note: The D, F, and K series waste numbers and Appendix VIII to Part 261 -- Hazardous Constituents were not included. Please refer to 40 CFR Part 261.

EPA SARA Title III, Extremely Hazardous Substance List for CAS108-31-6 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA SARA Title III, Community Right-to-Know for CAS108-31-6 (40 CFR 372.65, 2006; 40 CFR 372.28, 2006):

Listed as: Maleic anhydride
Effective Date for Reporting Under 40 CFR 372.30: 1/1/87
Lower Thresholds for Chemicals of Special Concern under 40 CFR 372.28:

DOT List of Marine Pollutants for CAS108-31-6 (49 CFR 172.101 - App. B, 2005):

Not Listed

EPA TSCA Inventory for CAS108-31-6 (EPA, 2005):

Listed as: 2,5-Furandione

SHIPPING REGULATIONS

SURFACE

DOT -- Table of Hazardous Materials and Special Provisions for UN/NA Number 2215 (49 CFR 172.101, 2005):

Hazardous materials descriptions and proper shipping name: Maleic anhydride

Symbol(s): Not Listed
Hazard class or Division: 8

8: Corrosive material. See 49 CFR section 173.136 for definitions.

Identification Number: UN2215
Packing Group: III

III: Packing Group III - indicates the degree of danger presented by the material is minor.

Label(s) required (if not excepted): 8

8: Corrosive.

Special Provisions: IB8, IP3, T1, TP33

IB8: Authorized IBCs: Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2, 31HZ1 and 31HZ2); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2).
IP3: Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner.
T1: Minimum test pressure (bar): 1.5; Minimum shell thickness (in mm-reference steel) (See sxn.178.274(d)): sxn.178.274(d)(2); Pressure-relief requirements (See sxn.178.275(g)): Normal; Bottom opening requirements (See sxn.178.275(d)): sxn.178.275(d)(2).
TP33: The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the defnintion of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter.

Packaging Authorizations (refer to 49 CFR 173.***):

Exceptions: 154
Non-bulk packaging: 213
Bulk packaging: 240

Quantity Limitations:

Passenger aircraft or railcar: 25 kg
Cargo aircraft only: 100 kg

Vessel Stowage Requirements:

Vessel stowage location: A

A: The material may be stowed "on deck" or "under deck" on a cargo vessel and on a passenger vessel.

Vessel stowage other: Not Listed

Hazardous materials descriptions and proper shipping name: Maleic anhydride, molten

Symbol(s): Not Listed
Hazard class or Division: 8

8: Corrosive material. See 49 CFR section 173.136 for definitions.

Identification Number: UN2215
Packing Group: III

III: Packing Group III - indicates the degree of danger presented by the material is minor.

Label(s) required (if not excepted): 8

8: Corrosive.

Special Provisions: T4, TP3

T4: Minimum test pressure (bar): 2.65; Minimum shell thickness (in mm-reference steel) (See sxn.178.274(d)): sxn.178.274(d)(2); Pressure-relief requirements (See sxn.178.275(g)): Normal; Bottom opening requirements (See sxn.178.275(d)): sxn.178.275(d)(3).
TP3: The maximum degree of filling (in %) for solids transported above their melting points and for elevated temperature liquids shall be determined by the following: [Degree of filling = 95 x (dr/df)], where df and dr are the mean densities of the liquid at the mean temperature of the liquid during filling and the maximum mean bulk temperature during transport respectively.

Packaging Authorizations (refer to 49 CFR 173.***):

Exceptions: None
Non-bulk packaging: 213
Bulk packaging: 240

Quantity Limitations:

Passenger aircraft or railcar: Forbidden
Cargo aircraft only: Forbidden

Vessel Stowage Requirements:

Vessel stowage location: A

A: The material may be stowed "on deck" or "under deck" on a cargo vessel and on a passenger vessel.

Vessel stowage other: Not Listed

ICAO International Shipping Name for UN2215 (ICAO, 2002):

Proper Shipping Name: Maleic anhydride
UN Number: 2215
Proper Shipping Name: Maleic anhydride, molten
UN Number: 2215

LABELS

NFPA

NFPA Hazard Ratings for CAS108-31-6 (NFPA, 2002):

Listed as: Maleic Anhydride
Hazard Ratings:

Health Rating (Blue): 3

(3) Seriously toxic material. Short term exposure could cause serious temporary or residual injury even though prompt medical treatment is given. Includes known or suspect small animal carcinogens, mutagens, or teratogens.

Flammability Rating (Red): 1

(1) Slightly combustible. Materials that require considerable preheating before ignition can occur. This rating includes most ordinary combustible materials.

Instability Rating (Yellow): 1

(1) Materials which are normally stable, but which can become unstable at elevated temperatures and pressures, or which may react with water with some release of energy, but not violently.

Oxidizer/Water-Reactive Designation: Not Listed

-HANDLING AND STORAGE

SUMMARY

INDUSTRIAL CHEMICALS

Protective Equipment and Clothing:

Approved organic vapor-acid gas canister; chemical goggles and face shield; rubber gloves and boots; coveralls or rubber apron (HSDB , 1994).
Strict precautions should be taken to prevent contact of solutions with eyes or skin. There should be ready access to eye irritation bottles. Contact lenses should not be worn when working with this chemical (HSDB , 1994).
Respirator Selection (HSDB , 1994):

At 25 mg/cu m: Any supplied-air respirator operated in continuous-flow mode.
At 50 mg/cu m: Any self-contained breathing apparatus with a full facepiece.
At 2000 mg/cu m: Any self-contained breathing apparatus that has full facepiece and is operated in a pressure-demand or other positive-pressure mode.
Emergency or planned entry into unknown concentration or IDLH/immediately dangerous to life or health/ conditions:

Any self-contained breathing apparatus that has a full facepiece and is operated in a pressure-demand or other positive-pressure mode.
Any supplied-air respirator that has a full facepiece and is operated in pressure-demand or other positive-pressure mode in combination with an auxiliary self-contained breathing apparatus operated in pressure-demand or other positive pressure mode.

In case of chemical escape: Any air-purifying, full-facepiece respirator (gas mask) with chin-style, front- or back-mounted organic vapor canister having a high-efficiency particulate filter.

Promptly remove non-impervious clothing that becomes contaminated (HSDB , 1994). Contaminated protective clothing should be segregated in such a manner so that there is no direct personal contact by personnel who handle, dispose, or clean the clothing.

Quality assurance to ascertain the completeness of the cleaning procedures should be implemented before the decontaminated protective clothing is returned for reuse by the workers.
Contaminated clothing should not be taken home at end of shift, but should remain at employee's place of work for cleaning.

Keep sparks, flames, and other sources of ignition away. Keep material out of water sources and sewers. Avoid breathing vapors or dusts. Do not handle broken packages without protective equipment. Wash away any material which may have contacted the body with copious amounts of water or soap and water.
Avoid breathing vapors or dusts. Do not handle broken packages unless wearing appropriate personal protective equipment. Wash away material which may have contacted the body with copious amounts of water or soap and water (HSDB , 1994).

STORAGE

ROOM/CABINET RECOMMENDATIONS

Outside or detached storage is preferred (NFPA, 1991).
Store in a cool, dry, well-ventilated location (NFPA, 1991).

INCOMPATIBILITIES

Separate from alkalies, alkali metals, amines, and oxidizing materials (NFPA, 1991).
Maleic anhydride is stable under normal laboratory storage conditions (HSDB , 1993).

-PERSONAL PROTECTION

SUMMARY

RECOMMENDED PROTECTIVE CLOTHING - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

Wear positive pressure self-contained breathing apparatus (SCBA).
Wear chemical protective clothing that is specifically recommended by the manufacturer. It may provide little or no thermal protection.
Structural firefighters' protective clothing provides limited protection in fire situations ONLY; it is not effective in spill situations where direct contact with the substance is possible.

RESPIRATORY PROTECTION

Refer to "Recommendations for respirator selection" in the NIOSH Pocket Guide to Chemical Hazards on TOMES Plus(R) for respirator information.

PROTECTIVE CLOTHING

CHEMICAL PROTECTIVE CLOTHING. Search results for CAS 108-31-6.

All data are compiled from published sources and are NOT recommended specifically by Truven Health Analytics. The appearance of specific manufacturers or products in this section does not represent an endorsement by Truven Health Analytics. No attempt has been made to verify the data presented. All product recommendations should be confirmed with the specific manufacturer for verification of product performance.
CLOTHING

Plastic Laminate

DuPont Personal Protection

Responder

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None detected
Notes: Not Listed
Citation: (DuPont, 2002)

Responder Plus

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >480
Permeation Rate (mcg/cm2/min): None detected
Notes: Not Listed
Citation: (DuPont, 2002)

FOOTWEAR

Specific recommendations and test data for this product type were not found in the available manufacturers' product literature.

GLOVES

Specific recommendations and test data for this product type were not found in the available manufacturers' product literature.

GENERAL INFORMATION

This section provides a compilation of chemical resistance information and test data for specific protective clothing products. Chemical resistance information includes both degradation resistance ratings and permeation resistance data. This information is designed to assist in the selection of appropriate protective clothing. Only data on specific products and manufacturers are included. Generic information or recommendations are not provided since significant differences can exist in the chemical resistance for apparent similar product types.
Specific product information is organized by general product type (gloves, garments, and footwear), material type, and manufacturer. The category 'garments' may include totally encapsulating suits, splash suits, as well as other items (e.g., coveralls, jackets, and aprons). Specific manufacturers should be contacted to determine the features of available styles/models.
In addition to chemical resistance information, there are many critical variables in the selection of protective clothing which cannot be represented in this summary of the literature. Some factors to be considered in choosing protective clothing include, but are not limited to: overall clothing integrity, physical hazard resistance, durability, human factors, ease of decontamination, and cost. Overall clothing integrity refers to a specific design's ability to offer consistent protection for all clothing-covered areas of the body. Physical hazards include resisting the effects of abrasion, cuts, tears, and punctures. Human factors entail effects on wearer mobility, visibility, and hearing for garments; dexterity, tactility, and grip for gloves; ankle support and weight for footwear; and, any effect of the clothing on the function of the wearer. There are several variations in the design for gloves, garments, and footwear that affect these factors. Protective clothing must properly be sized and correctly fit the wearer to ensure its proper use and function.
As required in the U.S.A., protective clothing should be selected based on a risk assessment of the workplace. This risk assessment must account for the identification of existing as well as potential hazards and involve the recommendation of protective clothing appropriate for the identified hazards. Therefore, the recommendations in this section should not be used as the sole basis for decisions on choice of protective clothing, but rather should be used as a tool by qualified occupational health and safety professionals or other technically qualified persons in conjunction with a review of all mitigating factors. Consult the OSHA PPE Standard (29 CFR 1910.132 - 1910.138) for regulations and additional guidance regarding the selection and use of protective clothing and equipment. For general information on protective clothing selection, refer to the "PERSONAL PROTECTIVE EQUIPMENT - OSHA PUB 3077" document.
PROTECTIVE CLOTHING SELECTION

Determine the type of protective clothing item needed based on a risk assessment (e.g., gloves, garments, footwear).
For high risk situations, choose clothing that covers all parts of the body that may be exposed. In many cases, multiple clothing items will be required. Low risk situations may permit partial body protective clothing. Select protective clothing products that have reported chemical resistance data. High risk situations involving full body clothing or extended chemical contact often require permeation resistance data to determine the barrier effectiveness of materials used in the construction of clothing. Relatively low risk situations, where only splash or incidental exposure occur, may allow use of protective clothing based on degradation or penetration resistance data. Specifics on the interpretation of chemical resistance data are presented below.
Other factors must be considered in addition to chemical resistance. The selected chemical protective clothing item should offer the optimal combination of protection against identified hazards while allowing maximum function and comfort.

INTERPRETATION OF DEGRADATION RATINGS

Degradation refers to physical changes in a material as the result of chemical exposure. Degradation may become evident in visible changes, such as discoloration, swelling, delamination, deterioration, or disintegration. Degradation effects may also be measured by weight change or other changes in a material's physical properties (e.g., strength, elasticity, hardness).
Degradation resistance ratings are provided by manufacturers to rate the amount of degradation that occurs for a particular protective clothing material when contacted by a chemical. All degradation ratings are qualitative and include ratings, such as "EXCELLENT," "GOOD," "FAIR," "POOR," and "NOT RECOMMENDED." There is no standard test method for the measurement of chemical degradation resistance; therefore, manufacturer ratings may be based on different testing approaches. This makes comparison of degradation ratings between manufacturers unreliable.
The use of degradation resistance ratings alone to recommend protective clothing, particularly for high hazard situations, should be avoided. Degradation resistance testing does not directly assess the barrier quality of protective clothing, since materials can show relatively little degradation but still allow either permeation or penetration by a chemical. Degradation resistance ratings can be used to exclude protective clothing materials from consideration. Protective clothing materials with a "NOT RECOMMENDED" degradation resistance rating should never be used.
For some products, the rating "NO PENETRATION" is provided. This refers to penetration resistance test results that are based on a different procedure (American Society for Testing and Materials (ASTM) Standard Test Method F 903). Penetration resistance testing involves placing a material sample in a test cell, exposing the exterior side of the material to a chemical, and then observing the interior side of the material for visible signs of liquid penetration. Part of the test is conducted at an elevated pressure. Test results are reported as pass (no penetration) or fail (penetration detected). Unlike degradation testing, penetration testing provides an assessment of protective clothing material barrier performance. Since penetration resistance testing examines only observable amounts of liquid penetration, permeation may still occur. The use of penetration resistance data must be restricted to liquid chemicals, and should be limited to scenarios where there is no reasonable vapor exposure hazard under the conditions of exposure.

INTERPRETATION OF PERMEATION DATA

Permeation is the process of chemical movement through a material on a molecular level. Permeation resistance refers to the ability of a material to retard or prevent chemical movement through it. Permeation may occur without any visible signs of degradation.
Permeation resistance is measured using a test cell which is divided into two halves by a protective clothing specimen. Chemical is placed on the challenge side, while the collection side is periodically monitored for permeating chemical. Permeation data were obtained in accordance with the American Society for Testing and Materials (ASTM) Standard Test Method F 739 (Resistance of Materials Used in Protective Clothing to Permeation by Liquids and Gases), unless stated otherwise. In the case of chemicals that are classified as warfare agents, the data were obtained in accordance with the Military Standard 282 (MIL-STD-282) (Military Standard, Filter Units, Protective Clothing, Gas-Mask Components, and Related Products: Performance Test Methods).
Permeation rate is the amount of chemical that passes through a material for a measured surface area per unit time. In this section, permeation rate is expressed in micrograms per square centimeter per minute (mcg/cm(2)/min). The reported permeation rate is either the steady-state rate or the maximum rate observed during testing. In some cases, very large permeation rates exceed measurement techniques and are reported as ">" (greater than) or "HIGH."
Breakthrough time is the elapsed time, in minutes, from the time the chemical comes in contact with the material exterior surface, to the time that chemical is detected on the interior surface. When no breakthrough is detected, the breakthrough time is report as ">" the testing period. If permeation breakthrough is rapid, results are reported as "<" (less than) the earlier sampling time or as "IMMEDIATELY" (which usually means breakthrough in less than 4 minutes).
The breakthrough time should exceed the expected use period of the selected protective clothing. Additionally, there are several other factors that must be taken into account to provide appropriate protection.
Permeation testing is usually conducted with full strength, undiluted chemical for the duration of the test period. Actual exposures may involve diluted chemical for short or intermittent exposure periods.
Permeation testing is usually conducted at room temperature. Permeation occurs faster at elevated temperatures (short breakthrough times and higher permeation rates) and slower at reduced temperatures (long breakthrough times and lower permeation rates).
Permeation resistance of mixtures cannot usually be determined on the basis of the individual chemicals making up the mixture. Synergistic effects may occur and result in more rapid permeation than accounted for by the individual mixture chemicals.
Permeation rates may be used to calculate potential wearer exposure; however, several assumptions must be made about the extent of exposure and condition of clothing wear. Furthermore, there are few chemicals with dermal exposure limits, making it difficult to determine an acceptable skin exposure level.

COMPANY INFORMATION

DuPont Personal Protection P. O. Box 80705 Wilmington, DE 19880-0705 USA Phone: (302) 774-1000 Toll-Free: (800) 931-3456 Website: http://personalprotection.dupont.com Email: personalprotection@usa.dupont.com

REFERENCES

CHEMICAL PROTECTIVE CLOTHING CITATIONS

The following sources were consulted for chemical protective clothing data:

(Ansell-Edmont, 2001)
(Bata Shoe Company, 1995)
(Best Manufacturing, 2002)
(Best Manufacturing, 2004)
(Boss Manufacturing Company, 1998)
(ChemFab Corporation, 1993)
(Comasec Safety, Inc., 2003)
(Comasec Safety, Inc., 2003a)
(DuPont, 2002)
(DuPont, 2002)
(DuPont, 2003)
(Guardian Manufacturing Group, 2001)
(ILC Dover, Inc., 1998)
(Kappler Inc., 2001)
(Kimberly-Clark, 2002)
(LaCrosse-Rainfair, 1997)
(MAPA Professional, 2003)
(MAPA Professional, 2004)
(Mar-Mac Manufacturing, Inc, 1995)
(Marigold Industrial, 2003)
(Memphis Glove Company, 2001)
(Montgomery Safety Products, 1995)
(Nat-Wear, 2001)
(Neese Industries, Inc., 2003)
(North, 2002)
(North, 2002)
(Playtex, 1995)
(River City, 1995)
(Safety 4, 2002)
(Servus, 1995)
(Standard Safety Equipment, 1995)
(Tingley, 2002)
(Trelleborg-Viking, Inc., 2001)
(Trelleborg-Viking, Inc., 2002)
(Wells Lamont Industrial, 2002)
(Workrite, 1997)

-PHYSICAL HAZARDS

FIRE HAZARD

SUMMARY

POTENTIAL FIRE OR EXPLOSION HAZARDS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)
- Combustible material: may burn but does not ignite readily.
- Substance will react with water (some violently) releasing flammable, toxic or corrosive gases and runoff.
- When heated, vapors may form explosive mixtures with air: indoors, outdoors and sewers explosion hazards.
- Most vapors are heavier than air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks).
- Vapors may travel to source of ignition and flash back.
- Contact with metals may evolve flammable hydrogen gas.
- Containers may explode when heated or if contaminated with water.
Maleic anhydride is combustible when exposed to heat or flame (Lewis, 1992).
It can react vigorously on contact with oxidizing materials (Lewis, 1992).

FLAMMABILITY CLASSIFICATION

NFPA Flammability Rating for CAS108-31-6 (NFPA, 2002):

Listed as: Maleic Anhydride
Flammability Rating: 1

(1) Slightly combustible. Materials that require considerable preheating before ignition can occur. This rating includes most ordinary combustible materials.

FIRE CONTROL/EXTINGUISHING AGENTS

FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

Note: Most foams will react with the material and release corrosive/toxic gases.

SMALL FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

CO2, dry chemical, dry sand, alcohol-resistant foam.

LARGE FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

Water spray, fog or alcohol-resistant foam.
FOR CHLOROSILANES, DO NOT USE WATER; use AFFF alcohol-resistant medium expansion foam.
Move containers from fire area if you can do it without risk.
Use water spray or for; do not use straight streams.

TANK OR CAR/TRAILER LOAD FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

Fight fire from maximum distance or use unmanned hose holders or monitor nozzles.
Do not get water inside containers.
Cool containers with flooding quantities of water until well after fire is out.
Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank.
ALWAYS stay away from tanks engulfed in fire.

NFPA Extinguishing Methods for CAS108-31-6 (NFPA, 2002):

Listed as: Maleic Anhydride
Extinguishing Method(s): 5, 2

5: Flammable liquid fires can be extinguished using carbon dioxide, dry chemical, foam, and vaporizing liquid extinguishers, as long as the fires are small to moderate in size and the flammable liquid reservoir is shallow. Use of foam to form a blanket over a flammable liquid is not effective when the liquid is water-soluble. Certain alcohol resistant foams are effective extinguishing agents for polar, non-polar, and water-soluble liquid fires. These foams are preferred for fighting flammable liquid fires except those that involve water reactive flammable liquids.
2: "Water or foam may cause frothing" refers to a situation where materials with a flash point above 212 degrees F (100 degrees C) are burning. Potentially violent frothing can be dangerous to fire fighters near the burning liquid. However, when highly viscous liquids are burning, fire fighters can intentionally cause frothing on the liquid surface to prevent further introduction of oxygen.

Water stream or foam may cause frothing. Use dry chemical, carbon dioxide, or water spray (NFPA, 1991).

COMBUSTION TOXICITY

When heated to decomposition (above 150 degrees C), maleic anhydride emits acrid smoke and irritating fumes (Lewis, 1992).
Maleic anhydride decomposes exothermically, evolving carbon dioxide in the presence of dimethylamine, triethylamine, pyridine, or quinoline at temperatures above 150 degrees C (HSDB , 1993).

EXPLOSION HAZARD

Maleic anhydride is explosive in the form of vapor when exposed to heat or flame (Lewis, 1992).

Maleic anhydride forms violent reactions with the following (Lewis, 1992):

Alkali metals (eg, sodium; potassium)
Amines (eg, dimethylamine; triethylamine)
Bases (eg, sodium hydroxide; potassium hydroxide; calcium hydroxide)
Lithium
Pyridine

DUST/VAPOR HAZARD

Maleic anhydride is explosive in the form of vapor when exposed to heat or flame (Lewis, 1992).

On dry skin the dust may result in a delayed burning sensation, but on moist skin the sensation is almost immediate, producing erythema, which may progress to vesiculation. Prolonged or repeated exposure also may cause dermatitis (Hathaway et al, 1991).

REACTIVITY HAZARD

Maleic anhydride is combustible when exposed to heat or flame (Lewis, 1992).

It can react vigorously on contact with oxidizing materials (Lewis, 1992).

Maleic anhydride reacts with water or steam to produce heat (Lewis, 1992).

It is incompatible with cations (Lewis, 1992).

When heated to decomposition (above 150 degrees C), maleic anhydride emits acrid smoke and irritating fumes (Lewis, 1992).

Maleic anhydride decomposes exothermically, evolving carbon dioxide in the presence of dimethylamine, triethylamine, pyridine, or quinoline at temperatures above 150 degrees C (HSDB , 1993).

This compound is explosive in the form of vapor when exposed to heat or flame (Lewis, 1992).

Maleic anhydride forms violent reactions with the following (Lewis, 1992):

Alkali metals (eg, sodium; potassium)
Amines (eg, dimethylamine; triethylamine)
Bases (eg, sodium hydroxide; potassium hydroxide; calcium hydroxide)
Lithium
Pyridine

EVACUATION PROCEDURES

SUMMARY

Editor's Note: This material is not listed in the Table of Initial Isolation and Protective Action Distances.

SPILL - PUBLIC SAFETY EVACUATION DISTANCES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

Increase, in the downwind direction, as necessary, the isolation distance of at least 50 meters (150 feet) for liquids and 25 meters (75 feet) for solids in all directions.

FIRE - PUBLIC SAFETY EVACUATION DISTANCES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions.

PUBLIC SAFETY MEASURES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)

CALL Emergency Response Telephone Number on Shipping Paper first. If Shipping Paper not available or no answer, refer to appropriate telephone number:

MEXICO:

SETIQ:

01-800-00-214-00 in the Mexican Republic;
For calls originating in Mexico City and the Metropolitan Area: 5559-1588;
For calls originating elsewhere, call: 011-52-555-559-1588.

CENACOM:

01-800-00-413-00 in the Mexican Republic;
For calls originating in Mexico City and the Metropolitan Area: 5550-1496, 5550-1552, 5550-1485, or 5550-4885;
For calls originating elsewhere, call: 011-52-555-550-1496, or 011-52-555-550-1552; 011-52-555-550-1485, or 011-52-555-550-4885.

ARGENTINA:

CIQUIME:

0-800-222-2933 in the Republic of Argentina;
For calls originating elsewhere, call: +54-11-4613-1100.

BRAZIL:

PRÓ-QUÍMICA:

0-800-118270 (Toll-free in Brazil);
For calls originating elsewhere, call: +55-11-232-1144 (Collect calls are accepted).

COLUMBIA:

CISPROQUIM:

01-800-091-6012 in Colombia;
For calls originating in Bogotá, Colombia, call: 288-6012;
For calls originating elsewhere, call: 011-57-1-288-6012.

CANADA:

CANUTEC:

613-996-6666 (Collect calls are accepted);
*666 cellular (in Canada only).

UNITED STATES:

CHEMTREC®:

1-800-424-9300 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
703-527-3887 for calls originating elsewhere (Collect calls are accepted).

CHEM-TEL, INC.:

1-800-255-3924 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
813-248-0585 for calls originating elsewhere (Collect calls are accepted).

INFOTRAC:

1-800-535-5053 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
352-323-3500 for calls originating elsewhere (Collect calls are accepted).

3E COMPANY:

1-800-451-8346 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
760-602-8703 for calls originating elsewhere (Collect calls are accepted).

NATIONAL RESPONSE CENTER (NRC):

1-800-424-8802 - (24 hours) (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
202-267-2675 for calls in the District of Columbia.

MILITARY SHIPMENTS:

703-697-0218 - Explosives/ammunition incidents (Collect calls are accepted);
1-800-851-8061 - All other dangerous goods incidents.

NATIONWIDE POISON CONTROL CENTER (United States only):

1-800-222-1222 (Toll-free in the U.S.).

For additional details see the section entitled "WHO TO CALL FOR ASSISTANCE" under the ERG Instructions.
As an immediate precautionary measure, isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.
Keep unauthorized personnel away.
Stay upwind.
Keep out of low areas.
Ventilate enclosed areas.

AIHA ERPG Values for CAS108-31-6 (AIHA, 2006):

Listed as Maleic Anhydride
ERPG-1 (units = ppm): 0.2
ERPG-2 (units = ppm): 2
ERPG-3 (units = ppm): 20
Under Ballot, Review, or Consideration: No
Definitions:

ERPG-1: The ERPG-1 is the maximum airborne concentration below which it is believed nearly all individuals could be exposed for up to one hour without experiencing more than mild, transient adverse health effects or perceiving a clearly defined objectionable odor.
ERPG-2: The ERPG-2 is the maximum airborne concentration below which it is believed nearly all individuals could be exposed for up to one hour without experiencing or developing irreversible or other serious health effects or symptoms that could impair an individual's ability to take protective action.
ERPG-3: The ERPG-3 is the maximum airborne concentration below which it is believed nearly all individuals could be exposed for up to one hour without experiencing or developing life-threatening health effects.

DOE TEEL Values for CAS108-31-6 (U.S. Department of Energy, Office of Emergency Management, 2010):

Listed as Maleic anhydride
TEEL-0 (units = ppm): 0.2
TEEL-1 (units = ppm): 0.2
TEEL-2 (units = ppm): 2
TEEL-3 (units = ppm): 20
Definitions:

TEEL-0: The threshold concentration below which most people will experience no adverse health effects.
TEEL-1: The airborne concentration (expressed as ppm [parts per million] or mg/m(3) [milligrams per cubic meter]) of a substance above which it is predicted that the general population, including susceptible individuals, could experience notable discomfort, irritation, or certain asymptomatic, nonsensory effects. However, these effects are not disabling and are transient and reversible upon cessation of exposure.
TEEL-2: The airborne concentration (expressed as ppm or mg/m(3)) of a substance above which it is predicted that the general population, including susceptible individuals, could experience irreversible or other serious, long-lasting, adverse health effects or an impaired ability to escape.
TEEL-3: The airborne concentration (expressed as ppm or mg/m(3)) of a substance above which it is predicted that the general population, including susceptible individuals, could experience life-threatening adverse health effects or death.

AEGL Values for CAS108-31-6 (National Research Council, 2010; National Research Council, 2009; National Research Council, 2008; National Research Council, 2007; NRC, 2001; NRC, 2002; NRC, 2003; NRC, 2004; NRC, 2004; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; United States Environmental Protection Agency Office of Pollution Prevention and Toxics, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; 62 FR 58840, 1997; 65 FR 14186, 2000; 65 FR 39264, 2000; 65 FR 77866, 2000; 66 FR 21940, 2001; 67 FR 7164, 2002; 68 FR 42710, 2003; 69 FR 54144, 2004):

Not Listed

NIOSH IDLH Values for CAS108-31-6 (National Institute for Occupational Safety and Health, 2007):

IDLH: 10 mg/m3
Note(s): Not Listed

CONTAINMENT/WASTE TREATMENT OPTIONS

SUMMARY

SPILL OR LEAK PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)
- ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area).
- All equipment used when handling the product must be grounded.
- Do not touch damaged containers or spilled material unless wearing appropriate protective clothing.
- Stop leak if you can do it without risk.
- A vapor suppressing foam may be used to reduce vapors.
- FOR CHLOROSILANES, use AFFF alcohol-resistant medium expansion foam to reduce vapors.
- DO NOT GET WATER on spilled substance or inside containers.
- Use water spray to reduce vapors or divert vapor cloud drift. Avoid allowing water runoff to contact spilled material.
- Prevent entry into waterways, sewers, basements or confined areas.
RECOMMENDED PROTECTIVE CLOTHING - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)
- Wear positive pressure self-contained breathing apparatus (SCBA).
- Wear chemical protective clothing that is specifically recommended by the manufacturer. It may provide little or no thermal protection.
- Structural firefighters' protective clothing provides limited protection in fire situations ONLY; it is not effective in spill situations where direct contact with the substance is possible.
"At the time of this review, criteria for land treatment or burial (sanitary landfill) disposal practices are subject to significant revision. Prior to implementing land disposal of waste residue (including waste sludge), consult with environmental regulatory agencies for guidance on acceptable disposal practices." (HSDB , 1993)
Generators of waste equal to or greater than 100 kg/month containing maleic anhydride, EPA Hazardous Waste Number U147, must conform with US Environmental Protection Agency regulations in storage, treatment, and disposal of the waste (40 CFR 260-270).
LAND SPILL (AAR, 1987)
- Dig a pit, pond, lagoon, or holding area to contain liquid or solid material.
- Cover solids with a plastic sheet to prevent dissolving in rain or fire fighting water.
WATER SPILL (AAR, 1987)
- If dissolved in region of 10 ppm or greater concentration, apply activated carbon at ten times the spilled amount.
- Use mechanical dredges or lifts to remove immobilized masses of pollutants and precipitates.
Maleic anhydride is a good candidate for rotary kiln incineration and fluidized bed incineration (HSDB , 1993).

SMALL LEAK/SPILL

SMALL SPILL PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 156 (ERG, 2004)
- Cover with DRY earth, DRY sand or other non-combustible material followed with plastic sheet to minimize spreading or contact with rain.
- Use clean non-sparking tools to collect material and place it into loosely covered plastic containers for later disposal.

-ENVIRONMENTAL HAZARD MANAGEMENT

POLLUTION HAZARD

AIR: Maleic anhydride released into the atmosphere will degrade by reaction with ozone and photochemically produced hydroxyl radicals (estimated half-life of 1.7 hours) (HSDB , 1993).

WATER: Maleic anhydride released into water will hydrolyze rapidly (half-life of 0.37 minutes) to maleic acid (HSDB , 1993).

SOIL: Maleic anhydride's fate in soil in unknown. However, since it biodegrades in sewage treatment plants and hydrolyzes, it's likely that it will degrade in soil. A combination of these processes should be important (HSDB , 1993).

ENVIRONMENTAL FATE AND KINETICS

OTHER

OTHER
- AIR: The estimated half-life of maleic anhydride in air is 1.7 hours. It will degrade by reaction with ozone and photochemically produced hydroxyl radicals (HSDB , 1993).
- WATER: The half-life of maleic anhydride in water via hydrolyzation is 0.37 minutes. It hydrolyzes to maleic acid (HSDB , 1993).

ENVIRONMENTAL TOXICITY

ECOTOXICITY VALUES:

TLm, Mosquito fish, 230 to 240 mg/L/24 to 96 hr, conditions of bioassay not specified (HSDB , 1993)
TLm, Sunfish, 150 ppm/24 hr, fresh water (CHRIS , 1993)

-PHYSICAL/CHEMICAL PROPERTIES

MOLECULAR WEIGHT

98.06 (Budavari, 1989)

DESCRIPTION/PHYSICAL STATE

This compound exists as fused black or white crystals or colorless needles (Lewis, 1992; Sax & Lewis, 1987; ACGIH, 1986). It has a penetrating, acrid, choking odor (CHRIS , 1993; NFPA, 1991). It is generally colorless in solution (OHM/TADS , 1994). Orthorhomic needles are derived from chloroform (HSDB , 1994). The commercial grades are furnished in fused form, as briquettes (Budavari, 1989).

No information found at the time of this review.

VAPOR PRESSURE

1 mmHg (at 44.0 degrees C) (Lewis, 1992)

SPECIFIC GRAVITY

OTHER TEMPERATURE AND/OR PRESSURE

1.48 (at 20/4 degrees C) (Lewis, 1992; Budavari, 1989)
0.934 (at 20/4 degrees C) (Sax & Lewis, 1987; ACGIH, 1986)

FREEZING/MELTING POINT

MELTING POINT

52.8 degrees C (Budavari, 1989)

BOILING POINT

202 degrees C (at 760 mmHg) (Budavari, 1989)

179.5 degrees C (at 400 mmHg) (Budavari, 1989)

155.9 degrees C (at 200 mmHg) (Budavari, 1989)

135.8 degrees C (at 100 mmHg) (Budavari, 1989)

122 degrees C (at 60 mmHg) (Budavari, 1989)

111.8 degrees C (at 40 mmHg) (Budavari, 1989)

95 degrees C (at 20 mmHg) (Budavari, 1989)

78.7 degrees C (at 10 mmHg) (Budavari, 1989)

63.4 degrees C (at 5 mmHg) (Budavari, 1989)

FLASH POINT

215 degrees F (closed cup) (Lewis, 1992)

AUTOIGNITION TEMPERATURE

890 degrees F (Lewis, 1992)

EXPLOSIVE LIMITS

LOWER

1.4% (Lewis, 1992)

UPPER

7.1% (Lewis, 1992)

SOLUBILITY

IN WATER

Maleic anhydride is soluble in water at 30 degrees C, forming maleic acid (Budavari, 1989; Lewis, 1992; HSDB , 1994).
Solubility at 25 degrees C:

227 g/100 g (HSDB , 1994)
163,000 ppm (OHM/TADS , 1994)

IN ORGANIC SOLVENTS

Maleic anhydride is soluble in dioxane and soluble in alcohol with ester formation (Budavari, 1989; HSDB , 1994).
Solubility at 25 degrees C (g/100 g) (Budavari, 1989):

Acetone: 227
Benzene: 50
Carbon tetrachloride: 0.60
Chloroform: 52.5
Ethyl acetate: 112
Ligroin: 0.25
Toluene: 23.4
o-Xylene: 19.4

-REFERENCES

GENERAL BIBLIOGRAPHY

40 CFR 372.28: Environmental Protection Agency - Toxic Chemical Release Reporting, Community Right-To-Know, Lower thresholds for chemicals of special concern. National Archives and Records Administration (NARA) and the Government Printing Office (GPO). Washington, DC. Final rules current as of Apr 3, 2006.

40 CFR 372.65: Environmental Protection Agency - Toxic Chemical Release Reporting, Community Right-To-Know, Chemicals and Chemical Categories to which this part applies. National Archives and Records Association (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Apr 3, 2006.

49 CFR 172.101 - App. B: Department of Transportation - Table of Hazardous Materials, Appendix B: List of Marine Pollutants. National Archives and Records Administration (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Aug 29, 2005.

49 CFR 172.101: Department of Transportation - Table of Hazardous Materials. National Archives and Records Administration (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Aug 11, 2005.

62 FR 58840: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 1997.

65 FR 14186: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

65 FR 39264: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

65 FR 77866: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

66 FR 21940: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2001.

67 FR 7164: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2002.

68 FR 42710: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2003.

69 FR 54144: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2004.

AAR: Emergency Handling of Hazardous Materials in Surface Transportation. Hazardous Materials Systems (BOE), Association of American Railroads, Washington, DC, 1987, pp 426.

ACGIH: Documentation of the Threshold Limit Values and Biological Exposure Indices, 5th ed, Am Conference of Govt Ind Hyg, Inc, Cincinnati, OH, 1986, pp 353.

AIHA: 2006 Emergency Response Planning Guidelines and Workplace Environmental Exposure Level Guides Handbook, American Industrial Hygiene Association, Fairfax, VA, 2006.

American Conference of Governmental Industrial Hygienists : ACGIH 2010 Threshold Limit Values (TLVs(R)) for Chemical Substances and Physical Agents and Biological Exposure Indices (BEIs(R)), American Conference of Governmental Industrial Hygienists, Cincinnati, OH, 2010.

Ansell-Edmont: SpecWare Chemical Application and Recommendation Guide. Ansell-Edmont. Coshocton, OH. 2001. Available from URL: http://www.ansellpro.com/specware. As accessed 10/31/2001.

Artigas A, Bernard GR, Carlet J, et al: The American-European consensus conference on ARDS, part 2: ventilatory, pharmacologic, supportive therapy, study design strategies, and issues related to recovery and remodeling.. Am J Respir Crit Care Med 1998; 157:1332-1347.

Azuara-Blanco A, Pillai CT, & Dua HS: Amniotic membrane transplantation for ocular surface reconstruction. Br J Ophthalmol 1999; 83:399-402.

Bata Shoe Company: Industrial Footwear Catalog, Bata Shoe Company, Belcamp, MD, 1995.

Best Manufacturing: ChemRest Chemical Resistance Guide. Best Manufacturing. Menlo, GA. 2002. Available from URL: http://www.chemrest.com. As accessed 10/8/2002.

Best Manufacturing: Degradation and Permeation Data. Best Manufacturing. Menlo, GA. 2004. Available from URL: http://www.chemrest.com/DomesticPrep2/. As accessed 04/09/2004.

Boss Manufacturing Company: Work Gloves, Boss Manufacturing Company, Kewanee, IL, 1998.

Bretherick L: Bretherick's Handbook of Reactive Chemical Hazards, 4th ed, Butterworths, London, England, 1990.

Brodovsky SC, McCarty AC, & Snibson G: Management of alkali burns an 11-year retrospective review. Ophthalmology 2000; 107:1829-1835.

Brodovsky SC, McCarty CA, & Snibson G: Management of alkali burns an 11-year retrospective review. Ophthalmology 2000a; 107:1829-1835.

Brodovsky SC, McCarty CA, & Snibson G: Management of alkali burns an 11-year review. Ophthalmology 2000b; 107:1829-1835.

Brower RG, Matthay AM, & Morris A: Ventilation with lower tidal volumes as compared with traditional tidal volumes for acute lung injury and the acute respiratory distress syndrome. N Eng J Med 2000; 342:1301-1308.

Budavari S: The Merck Index, 11th ed, Merck & Co, Inc, Rahway, NJ, 1989, pp 895-896.

Burgess JL, Kirk M, Borron SW, et al: Emergency department hazardous materials protocol for contaminated patients. Ann Emerg Med 1999; 34(2):205-212.

CHRIS : CHRIS Hazardous Chemical Data. US Department of Transportation, US Coast Guard. Washington, DC (Internet Version). Edition expires 1993; provided by Truven Health Analytics Inc., Greenwood Village, CO.

CHRIS : CHRIS Hazardous Chemical Data. US Department of Transportation, US Coast Guard. Washington, DC (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Caravati EM: Alkali. In: Dart RC, ed. Medical Toxicology, Lippincott Williams & Wilkins, Philadelphia, PA, 2004.

Carvajal HF & Stewart CE: Emergency management of burn patients: the first few hours. Emerg Med Reports 1987; 8:129-136.

Cataletto M: Respiratory Distress Syndrome, Acute(ARDS). In: Domino FJ, ed. The 5-Minute Clinical Consult 2012, 20th ed. Lippincott Williams & Wilkins, Philadelphia, PA, 2012.

ChemFab Corporation: Chemical Permeation Guide Challenge Protective Clothing Fabrics, ChemFab Corporation, Merrimack, NH, 1993.

Clayton GD & Clayton FE: Patty's Industrial Hygiene and Toxicology, Toxicology, 3rd ed, John Wiley & Sons, New York, NY, 1981.

Comasec Safety, Inc.: Chemical Resistance to Permeation Chart. Comasec Safety, Inc.. Enfield, CT. 2003. Available from URL: http://www.comasec.com/webcomasec/english/catalogue/mtabgb.html. As accessed 4/28/2003.

Comasec Safety, Inc.: Product Literature, Comasec Safety, Inc., Enfield, CT, 2003a.

DFG: List of MAK and BAT Values 2002, Report No. 38, Deutsche Forschungsgemeinschaft, Commission for the Investigation of Health Hazards of Chemical Compounds in the Work Area, Wiley-VCH, Weinheim, Federal Republic of Germany, 2002.

DuPont: DuPont Suit Smart: Interactive Tool for the Selection of Protective Apparel. DuPont. Wilmington, DE. 2002. Available from URL: http://personalprotection.dupont.com/protectiveapparel/suitsmart/smartsuit2/na_english.asp. As accessed 10/31/2002.

DuPont: Permeation Guide for DuPont Tychem Protective Fabrics. DuPont. Wilmington, DE. 2003. Available from URL: http://personalprotection.dupont.com/en/pdf/tyvektychem/pgcomplete20030128.pdf. As accessed 4/26/2004.

DuPont: Permeation Test Results. DuPont. Wilmington, DE. 2002a. Available from URL: http://www.tyvekprotectiveapprl.com/databases/default.htm. As accessed 7/31/2002.

EPA: Search results for Toxic Substances Control Act (TSCA) Inventory Chemicals. US Environmental Protection Agency, Substance Registry System, U.S. EPA's Office of Pollution Prevention and Toxics. Washington, DC. 2005. Available from URL: http://www.epa.gov/srs/.

ERG: Emergency Response Guidebook. A Guidebook for First Responders During the Initial Phase of a Dangerous Goods/Hazardous Materials Incident, U.S. Department of Transportation, Research and Special Programs Administration, Washington, DC, 2004.

Ernst AA, Thomson T, & Haynes ML: Warmed versus room temperature saline solution for ocular irrigation: a randomized clinical trial. Ann Emerg Med 1998; 32:676-679.

Fish R & Davidson RS: Management of ocular thermal and chemical injuries, including amniotic membrane therapy. Curr Opin Ophthalmol 2010; 21(4):317-321.

Grant WM & Schuman JS: Toxicology of the Eye, 4th ed, Charles C Thomas, Springfield, IL, 1993.

Grant WM & Schuman JS: Toxicology of the Eye, 4th ed, Charles C Thomas, Springfield, IL, 1993a.

Grant WM: Toxicology of the Eye, 3rd ed, Charles C Thomas Publisher, Springfield, IL, 1986.

Guardian Manufacturing Group: Guardian Gloves Test Results. Guardian Manufacturing Group. Willard, OH. 2001. Available from URL: http://www.guardian-mfg.com/guardianmfg.html. As accessed 12/11/2001.

Guerin JC: Poumon Coeur 1980; 36:393-395.

HSDB : Hazardous Substances Data Bank. National Library of Medicine. Bethesda, MD (Internet Version). Edition expires 1993; provided by Truven Health Analytics Inc., Greenwood Village, CO.

HSDB : Hazardous Substances Data Bank. National Library of Medicine. Bethesda, MD (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Haas CF: Mechanical ventilation with lung protective strategies: what works?. Crit Care Clin 2011; 27(3):469-486.

Hathaway GJ, Proctor NH, & Hughes JP: Chemical Hazards of the Workplace, 3rd ed, Van Nostrand Reinhold Company, New York, NY, 1991, pp 364-365.

Haynes BW Jr: Emergency department management of minor burns. Top Emerg Med 1981; 3:35-40.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: 1,3-Butadiene, Ethylene Oxide and Vinyl Halides (Vinyl Fluoride, Vinyl Chloride and Vinyl Bromide), 97, International Agency for Research on Cancer, Lyon, France, 2008.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Formaldehyde, 2-Butoxyethanol and 1-tert-Butoxypropan-2-ol, 88, International Agency for Research on Cancer, Lyon, France, 2006.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Household Use of Solid Fuels and High-temperature Frying, 95, International Agency for Research on Cancer, Lyon, France, 2010a.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Smokeless Tobacco and Some Tobacco-specific N-Nitrosamines, 89, International Agency for Research on Cancer, Lyon, France, 2007.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Some Non-heterocyclic Polycyclic Aromatic Hydrocarbons and Some Related Exposures, 92, International Agency for Research on Cancer, Lyon, France, 2010.

IARC: List of all agents, mixtures and exposures evaluated to date - IARC Monographs: Overall Evaluations of Carcinogenicity to Humans, Volumes 1-88, 1972-PRESENT. World Health Organization, International Agency for Research on Cancer. Lyon, FranceAvailable from URL: http://monographs.iarc.fr/monoeval/crthall.html. As accessed Oct 07, 2004.

ICAO: Technical Instructions for the Safe Transport of Dangerous Goods by Air, 2003-2004. International Civil Aviation Organization, Montreal, Quebec, Canada, 2002.

ILC Dover, Inc.: Ready 1 The Chemturion Limited Use Chemical Protective Suit, ILC Dover, Inc., Frederica, DE, 1998.

International Agency for Research on Cancer (IARC): IARC monographs on the evaluation of carcinogenic risks to humans: list of classifications, volumes 1-116. International Agency for Research on Cancer (IARC). Lyon, France. 2016. Available from URL: http://monographs.iarc.fr/ENG/Classification/latest_classif.php. As accessed 2016-08-24.

International Agency for Research on Cancer: IARC Monographs on the Evaluation of Carcinogenic Risks to Humans. World Health Organization. Geneva, Switzerland. 2015. Available from URL: http://monographs.iarc.fr/ENG/Classification/. As accessed 2015-08-06.

Jackson J & Jones AH: Haemolytic anaemia in a case of occupational asthma due to maleic anhydride. Brit J Ind Med 1993; 50:191-192.

Kappler, Inc.: Suit Smart. Kappler, Inc.. Guntersville, AL. 2001. Available from URL: http://www.kappler.com/suitsmart/smartsuit2/na_english.asp?select=1. As accessed 7/10/2001.

Keith LH & Walters DB: Compendium of Safety Data Sheets for Research and Industrial Chemicals. Parts I,II, and III, VCH Publishers, Deerfield Beach, FL, 1985.

Kimberly-Clark, Inc.: Chemical Test Results. Kimberly-Clark, Inc.. Atlanta, GA. 2002. Available from URL: http://www.kc-safety.com/tech_cres.html. As accessed 10/4/2002.

Kollef MH & Schuster DP: The acute respiratory distress syndrome. N Engl J Med 1995; 332:27-37.

Kuckelkorn R, Kottek A, & Schrage N: Poor prognosis of severe chemical and thermal eye burns: the need for adequate emergency care and primary prevention. Int Arch Occup Environ Health 1995; 281-284.

LaCrosse-Rainfair: Safety Products, LaCrosse-Rainfair, Racine, WI, 1997.

Leaver SK & Evans TW: Acute respiratory distress syndrome. BMJ 2007; 335(7616):389-394.

Lee HS, Wang YT, & Cheong TH: Occupational asthma due to maleic anhydride. Brit J Ind Med 1991; 48:283-285.

Lewis RJ: Sax's Dangerous Properties of Industrial Materials, 8th ed, Van Nostrand Reinhold Company, New York, NY, 1992, pp 2155-2156.

MAPA Professional: Chemical Resistance Guide. MAPA North America. Columbia, TN. 2003. Available from URL: http://www.mapaglove.com/pro/ChemicalSearch.asp. As accessed 4/21/2003.

MAPA Professional: Chemical Resistance Guide. MAPA North America. Columbia, TN. 2004. Available from URL: http://www.mapaglove.com/ProductSearch.cfm?id=1. As accessed 6/10/2004.

Mar-Mac Manufacturing, Inc: Product Literature, Protective Apparel, Mar-Mac Manufacturing, Inc., McBee, SC, 1995.

Marigold Industrial: US Chemical Resistance Chart, on-line version. Marigold Industrial. Norcross, GA. 2003. Available from URL: www.marigoldindustrial.com/charts/uschart/uschart.html. As accessed 4/14/2003.

Meller D, Pires RT, & Mack RJS: Amniotic membrane transplantation for acute chemical or thermal burns. Ophthalmology 2000; 107:980-990.

Memphis Glove Company: Permeation Guide. Memphis Glove Company. Memphis, TN. 2001. Available from URL: http://www.memphisglove.com/permeation.html. As accessed 7/2/2001.

Montgomery Safety Products: Montgomery Safety Products Chemical Resistant Glove Guide, Montgomery Safety Products, Canton, OH, 1995.

Morgan S & Murray A: Limbal autotransplantation in the acute and chronic phases of severe chemical injuries. Eye 1996; 10:349-354.

Moylan JA: Burn care after thermal injury. Top Emerg Med 1980; 2:39-52.

NFPA: Fire Protection Guide to Hazardous Materials, 10th ed, National Fire Protection Association, Quincy, MA, 1991.

NFPA: Fire Protection Guide to Hazardous Materials, 13th ed., National Fire Protection Association, Quincy, MA, 2002.

NHLBI ARDS Network: Mechanical ventilation protocol summary. Massachusetts General Hospital. Boston, MA. 2008. Available from URL: http://www.ardsnet.org/system/files/6mlcardsmall_2008update_final_JULY2008.pdf. As accessed 2013-08-07.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 1, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2001.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 2, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2002.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 3, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2003.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 4, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2004.

Naradzay J & Barish RA: Approach to ophthalmologic emergencies. Med Clin North Am 2006; 90(2):305-328.

Nat-Wear: Protective Clothing, Hazards Chart. Nat-Wear. Miora, NY. 2001. Available from URL: http://www.natwear.com/hazchart1.htm. As accessed 7/12/2001.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2,3-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2,4-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2-Butylene Oxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648083cdbb&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2-Dibromoethane (Proposed). United States Environmental Protection Agency. Washington, DC. 2007g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064802796db&disposition=attachment&contentType=pdf. As accessed 2010-08-18.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,3,5-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 2-Ethylhexyl Chloroformate (Proposed). United States Environmental Protection Agency. Washington, DC. 2007b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648037904e&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Acrylonitrile (Proposed). United States Environmental Protection Agency. Washington, DC. 2007c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648028e6a3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Adamsite (Proposed). United States Environmental Protection Agency. Washington, DC. 2007h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Agent BZ (3-quinuclidinyl benzilate) (Proposed). United States Environmental Protection Agency. Washington, DC. 2007f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ad507&disposition=attachment&contentType=pdf. As accessed 2010-08-18.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Allyl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648039d9ee&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Aluminum Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Arsenic Trioxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2007m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480220305&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Automotive Gasoline Unleaded (Proposed). United States Environmental Protection Agency. Washington, DC. 2009a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cc17&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Biphenyl (Proposed). United States Environmental Protection Agency. Washington, DC. 2005j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064801ea1b7&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bis-Chloromethyl Ether (BCME) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006n. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648022db11&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Boron Tribromide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ae1d3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bromine Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2007d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648039732a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bromoacetone (Proposed). United States Environmental Protection Agency. Washington, DC. 2008e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809187bf&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Calcium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Carbonyl Fluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ae328&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Carbonyl Sulfide (Proposed). United States Environmental Protection Agency. Washington, DC. 2007e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648037ff26&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Chlorobenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2008c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803a52bb&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Cyanogen (Proposed). United States Environmental Protection Agency. Washington, DC. 2008f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809187fe&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Dimethyl Phosphite (Proposed). United States Environmental Protection Agency. Washington, DC. 2009. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbf3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Diphenylchloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648091884e&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyl Phosphorodichloridate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480920347&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2008g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809203e7&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Germane (Proposed). United States Environmental Protection Agency. Washington, DC. 2008j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963906&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Hexafluoropropylene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064801ea1f5&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ketene (Proposed). United States Environmental Protection Agency. Washington, DC. 2007. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ee7c&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Magnesium Aluminum Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Magnesium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Malathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2009k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809639df&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Mercury Vapor (Proposed). United States Environmental Protection Agency. Washington, DC. 2009b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a8a087&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl Isothiocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963a03&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl Parathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2008l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963a57&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl tertiary-butyl ether (Proposed). United States Environmental Protection Agency. Washington, DC. 2007a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064802a4985&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methylchlorosilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2005. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5f4&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyldichlorosilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2005a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c646&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN1 CAS Reg. No. 538-07-8) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN2 CAS Reg. No. 51-75-2) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN3 CAS Reg. No. 555-77-1) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Tetroxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008n. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648091855b&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Trifluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963e0c&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Parathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2008o. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963e32&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Perchloryl Fluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e268&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Perfluoroisobutylene (Proposed). United States Environmental Protection Agency. Washington, DC. 2009d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e26a&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008p. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096dd58&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyl Mercaptan (Proposed). United States Environmental Protection Agency. Washington, DC. 2006d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020cc0c&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phorate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008q. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096dcc8&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phosgene (Draft-Revised). United States Environmental Protection Agency. Washington, DC. 2009e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a8a08a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phosgene Oxime (Proposed). United States Environmental Protection Agency. Washington, DC. 2009f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e26d&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Potassium Cyanide (Proposed). United States Environmental Protection Agency. Washington, DC. 2009g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbb9&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Potassium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Propargyl Alcohol (Proposed). United States Environmental Protection Agency. Washington, DC. 2006e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec91&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Selenium Hexafluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2006f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec55&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Silane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d523&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sodium Cyanide (Proposed). United States Environmental Protection Agency. Washington, DC. 2009h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbb9&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sodium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Strontium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sulfuryl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2006h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec7a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tear Gas (Proposed). United States Environmental Protection Agency. Washington, DC. 2008s. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e551&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tellurium Hexafluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e2a1&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tert-Octyl Mercaptan (Proposed). United States Environmental Protection Agency. Washington, DC. 2008r. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e5c7&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tetramethoxysilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d632&disposition=attachment&contentType=pdf. As accessed 2010-08-17.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethoxysilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d632&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethyl Phosphite (Proposed). United States Environmental Protection Agency. Washington, DC. 2009j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7d608&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethylacetyl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008t. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e5cc&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Zinc Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for n-Butyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064808f9591&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Heart,Lung,and Blood Institute: Expert panel report 3: guidelines for the diagnosis and management of asthma. National Heart,Lung,and Blood Institute. Bethesda, MD. 2007. Available from URL: http://www.nhlbi.nih.gov/guidelines/asthma/asthgdln.pdf.

National Institute for Occupational Safety and Health: NIOSH Pocket Guide to Chemical Hazards, U.S. Department of Health and Human Services, Centers for Disease Control and Prevention, Cincinnati, OH, 2007.

National Research Council : Acute exposure guideline levels for selected airborne chemicals, 5, National Academies Press, Washington, DC, 2007.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 6, National Academies Press, Washington, DC, 2008.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 7, National Academies Press, Washington, DC, 2009.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 8, National Academies Press, Washington, DC, 2010.

Neese Industries, Inc.: Fabric Properties Rating Chart. Neese Industries, Inc.. Gonzales, LA. 2003. Available from URL: http://www.neeseind.com/new/TechGroup.asp?Group=Fabric+Properties&Family=Technical. As accessed 4/15/2003.

North: Chemical Resistance Comparison Chart - Protective Footwear . North Safety. Cranston, RI. 2002. Available from URL: http://www.linkpath.com/index2gisufrm.php?t=N-USA1. As accessed April 30, 2004.

North: eZ Guide Interactive Software. North Safety. Cranston, RI. 2002a. Available from URL: http://www.northsafety.com/feature1.htm. As accessed 8/31/2002.

OHM/TADS : Oil and Hazardous Materials/Technical Assistance Data System. US Environmental Protection Agency. Washington, DC (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Peate WF: Work-related eye injuries and illnesses. Am Fam Physician 2007; 75(7):1017-1022.

Perry HD, Hodes LW, & Seedor JA: Effect of doxycycline hyclate on corneal epithelial wound healing in the rabbit alkali-burn model. Preliminary observations. Cornea 1993; 12:379-82.

Playtex: Fits Tough Jobs Like a Glove, Playtex, Westport, CT, 1995.

RTECS : Registry of Toxic Effects of Chemical Substances. National Institute for Occupational Safety and Health. Cincinnati, OH (Internet Version). Edition expires 1993; provided by Truven Health Analytics Inc., Greenwood Village, CO.

RTECS : Registry of Toxic Effects of Chemical Substances. National Institute for Occupational Safety and Health. Cincinnati, OH (Internet Version). Edition expires 1994; provided by Truven Health Analytics Inc., Greenwood Village, CO.

Randall DJ & Healy CE: J Am Coll Toxicol Pt B 1990; 1.

River City: Protective Wear Product Literature, River City, Memphis, TN, 1995.

Roberts JR: Minor burns (Pt II). Emerg Med Ambulatory Care News 1988; 10:4-5.

Ronk JF, Ruiz-Esmenjaud S, & Osorio M: Limbal conjunctival autograft in subacute alkaline corneal burn. Cornea 1994; 13:465-468.

Rosenberg N, Rousselin X, & Gervais P: Documents pour le medecin du travail 1988; 35:271-276.

Saari KM, Leinonen J, & Aine E: Management of chemical eye injuries with prolonged irrigation. Acta Ophthalmol Suppl 1984; 52-59.

Safety 4: North Safety Products: Chemical Protection Guide. North Safety. Cranston, RI. 2002. Available from URL: http://www.safety4.com/guide/set_guide.htm. As accessed 8/14/2002.

Sax NI & Lewis RJ: Hawley's Condensed Chemical Dictionary, 11th ed, Van Nostrand Reinhold Company, New York, NY, 1987, pp 725.

Seedor JA, Perry HD, & McNamara TF: Systemic tetracycline treatment of alkali-induced corneal ulceration in rabbits. Arch Ophthalmol 1987; 105:268-271.

Servus: Norcross Safety Products, Servus Rubber, Servus, Rock Island, IL, 1995.

Short RD, Johannsen FR, & Levinskas GJ: Teratology and multigeneration reproduction studies with maleic anhydride in rats. Fund Appl Toxicol 1986; 7:359-366.

Singh P, Tyagi M, Kumar Y, et al: Ocular chemical injuries and their management. Oman J Ophthalmol 2013; 6(2):83-86.

Smilkstein MJ & Fraunfelder F: Ophthalmic Principles, In: Goldfrank LR, Flomenbaum NE, Lewin NA, et al, eds. Goldfrank's Toxicologic Emergencies. 7th ed., McGraw-Hill, New York, NY, 2002.

Spector J & Fernandez WG: Chemical, thermal, and biological ocular exposures. Emerg Med Clin North Am 2008; 26(1):125-136.

Sridhar MS, Bansal AK, & Sangwan VS: Amniotic membrans transplantation in acute chemical and thermal injury. Am J Ophthalmol 2000; 130:134-137.

Standard Safety Equipment: Product Literature, Standard Safety Equipment, McHenry, IL, 1995.

Stolbach A & Hoffman RS: Respiratory Principles. In: Nelson LS, Hoffman RS, Lewin NA, et al, eds. Goldfrank's Toxicologic Emergencies, 9th ed. McGraw Hill Medical, New York, NY, 2011.

Su CY & Lin CP: Combined use of an amniotic membrane and tissue adhesive in treating corneal perforation: a case report. Ophtalmic Sufr Lasers 2000; 31:151-154.

Tingley: Chemical Degradation for Footwear and Clothing. Tingley. South Plainfield, NJ. 2002. Available from URL: http://www.tingleyrubber.com/tingley/Guide_ChemDeg.pdf. As accessed 10/16/2002.

Titiova NN & Zakirova RG: Kazan Med Zh 1977; 58:36-37.

Trelleborg-Viking, Inc.: Chemical and Biological Tests (database). Trelleborg-Viking, Inc.. Portsmouth, NH. 2002. Available from URL: http://www.trelleborg.com/protective/. As accessed 10/18/2002.

Trelleborg-Viking, Inc.: Trellchem Chemical Protective Suits, Interactive manual & Chemical Database. Trelleborg-Viking, Inc.. Portsmouth, NH. 2001.

Tuft SJ & Shortt AJ: Surgical rehabilitation following severe ocular burns. Eye (Lond) 2009; 23(10):1966-1971.

U.S. Department of Energy, Office of Emergency Management: Protective Action Criteria (PAC) with AEGLs, ERPGs, & TEELs: Rev. 26 for chemicals of concern. U.S. Department of Energy, Office of Emergency Management. Washington, DC. 2010. Available from URL: http://www.hss.doe.gov/HealthSafety/WSHP/Chem_Safety/teel.html. As accessed 2011-06-27.

U.S. Department of Health and Human Services, Public Health Service, National Toxicology Project : 11th Report on Carcinogens. U.S. Department of Health and Human Services, Public Health Service, National Toxicology Program. Washington, DC. 2005. Available from URL: http://ntp.niehs.nih.gov/INDEXA5E1.HTM?objectid=32BA9724-F1F6-975E-7FCE50709CB4C932. As accessed 2011-06-27.

U.S. Environmental Protection Agency: Discarded commercial chemical products, off-specification species, container residues, and spill residues thereof. Environmental Protection Agency's (EPA) Resource Conservation and Recovery Act (RCRA); List of hazardous substances and reportable quantities 2010b; 40CFR(261.33, e-f):77-.

U.S. Environmental Protection Agency: Integrated Risk Information System (IRIS). U.S. Environmental Protection Agency. Washington, DC. 2011. Available from URL: http://cfpub.epa.gov/ncea/iris/index.cfm?fuseaction=iris.showSubstanceList&list_type=date. As accessed 2011-06-21.

U.S. Environmental Protection Agency: List of Radionuclides. U.S. Environmental Protection Agency. Washington, DC. 2010a. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-sec302-4.pdf. As accessed 2011-06-17.

U.S. Environmental Protection Agency: List of hazardous substances and reportable quantities. U.S. Environmental Protection Agency. Washington, DC. 2010. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-sec302-4.pdf. As accessed 2011-06-17.

U.S. Environmental Protection Agency: The list of extremely hazardous substances and their threshold planning quantities (CAS Number Order). U.S. Environmental Protection Agency. Washington, DC. 2010c. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-part355.pdf. As accessed 2011-06-17.

U.S. Occupational Safety and Health Administration: Part 1910 - Occupational safety and health standards (continued) Occupational Safety, and Health Administration's (OSHA) list of highly hazardous chemicals, toxics and reactives. Subpart Z - toxic and hazardous substances. CFR 2010 2010; Vol6(SEC1910):7-.

U.S. Occupational Safety, and Health Administration (OSHA): Process safety management of highly hazardous chemicals. 29 CFR 2010 2010; 29(1910.119):348-.

United States Environmental Protection Agency Office of Pollution Prevention and Toxics: Acute Exposure Guideline Levels (AEGLs) for Vinyl Acetate (Proposed). United States Environmental Protection Agency. Washington, DC. 2006. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6af&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

Wells Lamont Industrial: Chemical Resistant Glove Application Chart. Wells Lamont Industrial. Morton Grove, IL. 2002. Available from URL: http://www.wellslamontindustry.com. As accessed 10/31/2002.

Willson DF, Truwit JD, Conaway MR, et al: The adult calfactant in acute respiratory distress syndrome (CARDS) trial. Chest 2015; 148(2):356-364.

Wilson DF, Thomas NJ, Markovitz BP, et al: Effect of exogenous surfactant (calfactant) in pediatric acute lung injury. A randomized controlled trial. JAMA 2005; 293:470-476.

Workrite: Chemical Splash Protection Garments, Technical Data and Application Guide, W.L. Gore Material Chemical Resistance Guide, Workrite, Oxnard, CA, 1997.

FeedBack

MALEIC ANHYDRIDE

Classification | Information to evaluate chemical incidents

Information to evaluate chemical incidents

Information to evaluate chemical incidents

Information to evaluate chemical incidents