ISOPROPYL ETHER

Isopropyl ether has CNS depressant and anesthetic properties similar to those of ethyl ether. It causes dermal irritation. The odor is irritating, and irritation of the eyes, nose, throat, and respiratory tract may be seen. The liquid itself is irritating to mucous membranes. Headache may be noted.

In experimental animals, no toxic effects have been noted other than dizziness and CNS and respiratory depression with death from respiratory arrest with exposure to very high concentrations.

POTENTIAL HEALTH HAZARDS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Inhalation or contact with material may irritate or burn skin and eyes.
Fire may produce irritating, corrosive and/or toxic gases.
Vapors may cause dizziness or suffocation.
Runoff from fire control may cause pollution.

-MEDICAL TREATMENT

LIFE SUPPORT

Support respiratory and cardiovascular function.

SUMMARY

FIRST AID - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Move victim to fresh air.
Call 911 or emergency medical service.
Give artificial respiration if victim is not breathing.
Administer oxygen if breathing is difficult.
Remove and isolate contaminated clothing and shoes.
In case of contact with substance, immediately flush skin or eyes with running water for at least 20 minutes.
Wash skin with soap and water.
In case of burns, immediately cool affected skin for as long as possible with cold water. Do not remove clothing if adhering to skin.
Keep victim warm and quiet.
Ensure that medical personnel are aware of the material(s) involved and take precautions to protect themselves.

FIRST AID

GENERAL -

Move victims of inhalation exposure from the toxic environment and administer 100 percent supplemental oxygen with assisted ventilation as required. Exposed eyes and skin should be copiously flushed with water.
Because of potential irritant and CNS depressant effects, emesis should not be induced in ingestions and gastric lavage done only with caution. Immediate dilution with milk or water might be beneficial.

ORAL EXPOSURE -

Do not induce emesis.
Significant esophageal or gastrointestinal tract irritation or burns may occur following ingestion. The possible benefit of early removal of some ingested material by cautious gastric lavage must be weighed against potential complications of bleeding or perforation.
GASTRIC LAVAGE: Consider after ingestion of a potentially life-threatening amount of poison if it can be performed soon after ingestion (generally within 1 hour). Protect airway by placement in the head down left lateral decubitus position or by endotracheal intubation. Control any seizures first.

CONTRAINDICATIONS: Loss of airway protective reflexes or decreased level of consciousness in unintubated patients; following ingestion of corrosives; hydrocarbons (high aspiration potential); patients at risk of hemorrhage or gastrointestinal perforation; and trivial or non-toxic ingestion.

ACTIVATED CHARCOAL: Administer charcoal as a slurry (240 mL water/30 g charcoal). Usual dose: 25 to 100 g in adults/adolescents, 25 to 50 g in children (1 to 12 years), and 1 g/kg in infants less than 1 year old.
If CNS and respiratory depression are present, ensure airway patency and adequacy of oxygenation and ventilation. Endotracheal intubation, supplemental oxygenation, and assisted ventilation could be required.
Observe patients with ingestion carefully for the possible development of esophageal or gastrointestinal tract irritation or burns. If signs or symptoms of esophageal irritation or burns are present, consider endoscopy to determine the extent of injury.
Carefully observe patients with ingestion exposure for the development of any systemic signs or symptoms and administer symptomatic treatment as necessary.

INHALATION EXPOSURE -

INHALATION: Move patient to fresh air. Monitor for respiratory distress. If cough or difficulty breathing develops, evaluate for respiratory tract irritation, bronchitis, or pneumonitis. Administer oxygen and assist ventilation as required. Treat bronchospasm with an inhaled beta2-adrenergic agonist. Consider systemic corticosteroids in patients with significant bronchospasm.
Respiratory tract irritation, if severe, can progress to pulmonary edema which may be delayed in onset up to 24 to 72 hours after exposure in some cases.
ACUTE LUNG INJURY: Maintain ventilation and oxygenation and evaluate with frequent arterial blood gases and/or pulse oximetry monitoring. Early use of PEEP and mechanical ventilation may be needed.
If CNS and respiratory depression are present, ensure airway patency and adequacy of oxygenation and ventilation. Endotracheal intubation, supplemental oxygenation, and assisted ventilation could be required.
If respiratory tract irritation or respiratory depression is evident, monitor arterial blood gases, chest x-ray, and pulmonary function tests.
Carefully observe patients with inhalation exposure for the development of any systemic signs or symptoms and administer symptomatic treatment as necessary.

EYE EXPOSURE -

DECONTAMINATION: Remove contact lenses and irrigate exposed eyes with copious amounts of room temperature 0.9% saline or water for at least 15 minutes. If irritation, pain, swelling, lacrimation, or photophobia persist after 15 minutes of irrigation, the patient should be seen in a healthcare facility.

DERMAL EXPOSURE -

DECONTAMINATION: Remove contaminated clothing and jewelry and place them in plastic bags. Wash exposed areas with soap and water for 10 to 15 minutes with gentle sponging to avoid skin breakdown. A physician may need to examine the area if irritation or pain persists (Burgess et al, 1999).
Treat dermal irritation or burns with standard topical therapy. Patients developing dermal hypersensitivity reactions may require treatment with systemic or topical corticosteroids or antihistamines.

-RANGE OF TOXICITY

MINIMUM LETHAL EXPOSURE

ANIMAL DATA

In rabbits, the minimum lethal dose was 5 to 6.5 grams/kg (ACGIH, 1986).
Inhalation exposure to 60,000 ppm for one hour was lethal in rabbits, monkeys, and guinea pigs (Proctor & Hughes, 1978). A four hour exposure to 16,000 ppm was lethal in rats (Proctor & Hughes, 1978).

MAXIMUM TOLERATED EXPOSURE

ROUTE OF EXPOSURE

The undiluted liquid is irritating to the skin and mucous membranes (ACGIH, 1986).
Human volunteers exposed to a concentration of 300 ppm noted an objectionable odor (ACGIH, 1986). At a concentration of 500 ppm for 15 minutes, no irritation was noted (ACGIH, 1986). With exposure to 800 ppm for 5 minutes, most individuals complained of eye and nasal irritation (ACGIH, 1986).

ANIMAL DATA

Inhalation exposure of experimental animals to a concentration of 1 percent caused CNS and respiratory depression, while no deleterious effects were noted at a concentration of 0.1 percent (ACGIH, 1986).

Carcinogenicity Ratings for CAS108-20-3 :

ACGIH (American Conference of Governmental Industrial Hygienists, 2010): Not Listed ; Listed as: Isopropyl ether
EPA (U.S. Environmental Protection Agency, 2011): Not Listed
IARC (International Agency for Research on Cancer (IARC), 2016; International Agency for Research on Cancer, 2015; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2010; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2010a; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2008; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2007; IARC Working Group on the Evaluation of Carcinogenic Risks to Humans, 2006; IARC, 2004): Not Listed
NIOSH (National Institute for Occupational Safety and Health, 2007): Not Listed ; Listed as: Isopropyl ether
MAK (DFG, 2002): Not Listed
NTP (U.S. Department of Health and Human Services, Public Health Service, National Toxicology Project ): Not Listed

TOXICITY AND RISK ASSESSMENT VALUES

EPA IRIS

EPA Risk Assessment Values for CAS108-20-3 (U.S. Environmental Protection Agency, 2011):

Not Listed

TOXICITY VALUES

References: RTECS, 1988
- LC50- (INHALATION)MOUSE:
- LC50- (INHALATION)RABBIT:
- LC50- (INHALATION)RAT:
- LD50- (INTRAPERITONEAL)MOUSE:
- LD50- (SKIN)RABBIT:
- LD50- (ORAL)RAT:

-STANDARDS AND LABELS

WORKPLACE STANDARDS

ACGIH TLV Values for CAS108-20-3 (American Conference of Governmental Industrial Hygienists, 2010):

Editor's Note: The listed values are recommendations or guidelines developed by ACGIH(R) to assist in the control of health hazards. They should only be used, interpreted and applied by individuals trained in industrial hygiene. Before applying these values, it is imperative to read the introduction to each section in the current TLVs(R) and BEI(R) Book and become familiar with the constraints and limitations to their use. Always consult the Documentation of the TLVs(R) and BEIs(R) before applying these recommendations and guidelines.

Adopted Value

Isopropyl ether

TLV:

TLV-TWA: 250 ppm
TLV-STEL: 310 ppm
TLV-Ceiling:

Notations and Endnotes:

Carcinogenicity Category: Not Listed
Codes: Not Listed
Definitions: Not Listed

TLV Basis - Critical Effect(s): Eye and URT irr
Molecular Weight: 102.17

For gases and vapors, to convert the TLV from ppm to mg/m(3):

[(TLV in ppm)(gram molecular weight of substance)]/24.45

For gases and vapors, to convert the TLV from mg/m(3) to ppm:

[(TLV in mg/m(3))(24.45)]/gram molecular weight of substance

AIHA WEEL Values for CAS108-20-3 (AIHA, 2006):

Not Listed

NIOSH REL and IDLH Values for CAS108-20-3 (National Institute for Occupational Safety and Health, 2007):

Listed as: Isopropyl ether
REL:

TWA: 500 ppm (2100 mg/m(3))
STEL:
Ceiling:
Carcinogen Listing: (Not Listed) Not Listed
Skin Designation: Not Listed
Note(s):

IDLH:

IDLH: 1400 ppm
Note(s): [10%LEL]

[10%LEL]: The 10%LEL designation is provided where the IDLH was based on 10% of the lower explosive limit. This is used for safety purposes in some cases even though toxicity is not indicative of irreversible health effects or impairment of escape exists only at higher concentrations.

OSHA PEL Values for CAS108-20-3 (U.S. Occupational Safety, and Health Administration (OSHA), 2010):

Listed as: Isopropyl ether
Table Z-1 for Isopropyl ether:

8-hour TWA:

ppm: 500

Parts of vapor or gas per million parts of contaminated air by volume at 25 degrees C and 760 torr.

mg/m3: 2100

Milligrams of substances per cubic meter of air. When entry is in this column only, the value is exact; when listed with a ppm entry, it is approximate.

Ceiling Value:
Skin Designation: No
Notation(s): Not Listed

OSHA List of Highly Hazardous Chemicals, Toxics, and Reactives for CAS108-20-3 (U.S. Occupational Safety and Health Administration, 2010):

Not Listed

ENVIRONMENTAL STANDARDS

EPA CERCLA, Hazardous Substances and Reportable Quantities for CAS108-20-3 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA CERCLA, Hazardous Substances and Reportable Quantities, Radionuclides for CAS108-20-3 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA RCRA Hazardous Waste Number for CAS108-20-3 (U.S. Environmental Protection Agency, 2010b):

Not Listed
Editor's Note: The D, F, and K series waste numbers and Appendix VIII to Part 261 -- Hazardous Constituents were not included. Please refer to 40 CFR Part 261.

EPA SARA Title III, Extremely Hazardous Substance List for CAS108-20-3 (U.S. Environmental Protection Agency, 2010):

Not Listed

EPA SARA Title III, Community Right-to-Know for CAS108-20-3 (40 CFR 372.65, 2006; 40 CFR 372.28, 2006):

Not Listed

DOT List of Marine Pollutants for CAS108-20-3 (49 CFR 172.101 - App. B, 2005):

Not Listed

EPA TSCA Inventory for CAS108-20-3 (EPA, 2005):

Listed as: Propane, 2,2'-oxybis-

SHIPPING REGULATIONS

SURFACE

DOT -- Table of Hazardous Materials and Special Provisions for UN/NA Number 1159 (49 CFR 172.101, 2005):

Hazardous materials descriptions and proper shipping name: Diisopropyl ether

Symbol(s): Not Listed
Hazard class or Division: 3

3: Flammable and combustible liquid. See 49 CFR section 173.120 for definitions.

Identification Number: UN1159
Packing Group: II

II: Packing Group II - indicates the degree of danger presented by the material is medium.

Label(s) required (if not excepted): 3

3: Flammable Liquid.

Special Provisions: IB2, T4, TP1

IB2: Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1). Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 °C (1.1 bar at 122 °F), or 130kPa at 55 °C (1.3 bar at 131 °F) are authorized.
T4: Minimum test pressure (bar): 2.65; Minimum shell thickness (in mm-reference steel) (See sxn.178.274(d)): sxn.178.274(d)(2); Pressure-relief requirements (See sxn.178.275(g)): Normal; Bottom opening requirements (See sxn.178.275(d)): sxn.178.275(d)(3).
TP1: The maximum degree of filling must not exceed the degree of filling determined by the following: [Degree of filling = 97/1+alpha(tr - tf)], where tr is the maximum mean bulk temperature during transport, and tf is the temperature in degrees celsius of the liquid during filling.

Packaging Authorizations (refer to 49 CFR 173.***):

Exceptions: 150
Non-bulk packaging: 202
Bulk packaging: 242

Quantity Limitations:

Passenger aircraft or railcar: 5 L
Cargo aircraft only: 60 L

Vessel Stowage Requirements:

Vessel stowage location: E

E: The material may be stowed "on deck" or "under deck" on a cargo vessel and on a passenger vessel carrying a number of passengers limited to not more than the larger of 25 passengers, or one passenger per each 3 m of overall vessel length, but is prohibited from carriage on passenger vessels in which the limiting number of passengers is exceeded.

Vessel stowage other: 40

40: Stow "clear of living quarters".

ICAO International Shipping Name for UN1159 (ICAO, 2002):

Proper Shipping Name: Diisopropyl ether
UN Number: 1159

LABELS

NFPA

NFPA Hazard Ratings for CAS108-20-3 (NFPA, 2002):

Listed as: Isopropyl Ether
Hazard Ratings:

Health Rating (Blue): 2

(2) Moderately toxic material. Intense or continued exposure could cause temporary incapacitation or possible residual injury unless prompt medical treatment is given.

Flammability Rating (Red): 3

(3) Flammable. Liquids and solids that can be ignited under almost all ambient temperature conditions. Including liquids with a flash point below 73 degrees F and a boiling point above 100 degrees F, solid materials which form coarse dusts that burn rapidly without becoming explosive, materials which burn rapidly by reason of self-contained oxygen (ie, organic peroxides), and materials which ignite spontaneously when exposed to air.

Instability Rating (Yellow): 1

(1) Materials which are normally stable, but which can become unstable at elevated temperatures and pressures, or which may react with water with some release of energy, but not violently.

Oxidizer/Water-Reactive Designation: Not Listed

-PERSONAL PROTECTION

SUMMARY

RECOMMENDED PROTECTIVE CLOTHING - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Wear positive pressure self-contained breathing apparatus (SCBA).
Structural firefighters' protective clothing will only provide limited protection.

A self-contained breathing apparatus should be worn (NFPA, 1986).

Wear protective clothing including rubber gloves, overalls, a face shield, and a self-contained breathing apparatus (ITI, 1985).

For normal handling procedures, appropriate clothing and eye protection should be worn to prevent prolonged or repetitive skin contact and eye splashes (Sittig, 1985). If nonimpervious clothing is wet or contaminated, it should be removed immediately and wet or contaminated skin immediately washed (Sittig, 1985).

Respiratory protection may be required at concentrations exceeding allowable workplace standards (Sittig, 1985). Adequate ventilation should be provided and workers should wear rubber gloves, an organic chemical cartridge respirator or air pack, and chemical goggles (ITI, 1985; CHRIS , 1985).

RESPIRATORY PROTECTION

A self-contained breathing apparatus should be worn (NFPA, 1986).

Wear protective clothing including rubber gloves, overalls, a face shield, and a self-contained breathing apparatus (ITI, 1985).

Refer to "Recommendations for respirator selection" in the NIOSH Pocket Guide to Chemical Hazards on TOMES Plus(R) for respirator information.

PROTECTIVE CLOTHING

CHEMICAL PROTECTIVE CLOTHING. Search results for CAS 108-20-3.

All data are compiled from published sources and are NOT recommended specifically by Truven Health Analytics. The appearance of specific manufacturers or products in this section does not represent an endorsement by Truven Health Analytics. No attempt has been made to verify the data presented. All product recommendations should be confirmed with the specific manufacturer for verification of product performance.
CLOTHING

Chlorinated Polyethylene

ILC Dover, Inc.

Chemturion

Degradation Rating: No Degradation Rating provided
Breakthrough Time (minutes): >180
Permeation Rate (mcg/cm2/min): Not Listed
Notes: Not Listed
Citation: (ILC Dover, Inc., 1998)

FOOTWEAR

Specific recommendations and test data for this product type were not found in the available manufacturers' product literature.

GLOVES

Specific recommendations and test data for this product type were not found in the available manufacturers' product literature.

GENERAL INFORMATION

This section provides a compilation of chemical resistance information and test data for specific protective clothing products. Chemical resistance information includes both degradation resistance ratings and permeation resistance data. This information is designed to assist in the selection of appropriate protective clothing. Only data on specific products and manufacturers are included. Generic information or recommendations are not provided since significant differences can exist in the chemical resistance for apparent similar product types.
Specific product information is organized by general product type (gloves, garments, and footwear), material type, and manufacturer. The category 'garments' may include totally encapsulating suits, splash suits, as well as other items (e.g., coveralls, jackets, and aprons). Specific manufacturers should be contacted to determine the features of available styles/models.
In addition to chemical resistance information, there are many critical variables in the selection of protective clothing which cannot be represented in this summary of the literature. Some factors to be considered in choosing protective clothing include, but are not limited to: overall clothing integrity, physical hazard resistance, durability, human factors, ease of decontamination, and cost. Overall clothing integrity refers to a specific design's ability to offer consistent protection for all clothing-covered areas of the body. Physical hazards include resisting the effects of abrasion, cuts, tears, and punctures. Human factors entail effects on wearer mobility, visibility, and hearing for garments; dexterity, tactility, and grip for gloves; ankle support and weight for footwear; and, any effect of the clothing on the function of the wearer. There are several variations in the design for gloves, garments, and footwear that affect these factors. Protective clothing must properly be sized and correctly fit the wearer to ensure its proper use and function.
As required in the U.S.A., protective clothing should be selected based on a risk assessment of the workplace. This risk assessment must account for the identification of existing as well as potential hazards and involve the recommendation of protective clothing appropriate for the identified hazards. Therefore, the recommendations in this section should not be used as the sole basis for decisions on choice of protective clothing, but rather should be used as a tool by qualified occupational health and safety professionals or other technically qualified persons in conjunction with a review of all mitigating factors. Consult the OSHA PPE Standard (29 CFR 1910.132 - 1910.138) for regulations and additional guidance regarding the selection and use of protective clothing and equipment. For general information on protective clothing selection, refer to the "PERSONAL PROTECTIVE EQUIPMENT - OSHA PUB 3077" document.
PROTECTIVE CLOTHING SELECTION

Determine the type of protective clothing item needed based on a risk assessment (e.g., gloves, garments, footwear).
For high risk situations, choose clothing that covers all parts of the body that may be exposed. In many cases, multiple clothing items will be required. Low risk situations may permit partial body protective clothing. Select protective clothing products that have reported chemical resistance data. High risk situations involving full body clothing or extended chemical contact often require permeation resistance data to determine the barrier effectiveness of materials used in the construction of clothing. Relatively low risk situations, where only splash or incidental exposure occur, may allow use of protective clothing based on degradation or penetration resistance data. Specifics on the interpretation of chemical resistance data are presented below.
Other factors must be considered in addition to chemical resistance. The selected chemical protective clothing item should offer the optimal combination of protection against identified hazards while allowing maximum function and comfort.

INTERPRETATION OF DEGRADATION RATINGS

Degradation refers to physical changes in a material as the result of chemical exposure. Degradation may become evident in visible changes, such as discoloration, swelling, delamination, deterioration, or disintegration. Degradation effects may also be measured by weight change or other changes in a material's physical properties (e.g., strength, elasticity, hardness).
Degradation resistance ratings are provided by manufacturers to rate the amount of degradation that occurs for a particular protective clothing material when contacted by a chemical. All degradation ratings are qualitative and include ratings, such as "EXCELLENT," "GOOD," "FAIR," "POOR," and "NOT RECOMMENDED." There is no standard test method for the measurement of chemical degradation resistance; therefore, manufacturer ratings may be based on different testing approaches. This makes comparison of degradation ratings between manufacturers unreliable.
The use of degradation resistance ratings alone to recommend protective clothing, particularly for high hazard situations, should be avoided. Degradation resistance testing does not directly assess the barrier quality of protective clothing, since materials can show relatively little degradation but still allow either permeation or penetration by a chemical. Degradation resistance ratings can be used to exclude protective clothing materials from consideration. Protective clothing materials with a "NOT RECOMMENDED" degradation resistance rating should never be used.
For some products, the rating "NO PENETRATION" is provided. This refers to penetration resistance test results that are based on a different procedure (American Society for Testing and Materials (ASTM) Standard Test Method F 903). Penetration resistance testing involves placing a material sample in a test cell, exposing the exterior side of the material to a chemical, and then observing the interior side of the material for visible signs of liquid penetration. Part of the test is conducted at an elevated pressure. Test results are reported as pass (no penetration) or fail (penetration detected). Unlike degradation testing, penetration testing provides an assessment of protective clothing material barrier performance. Since penetration resistance testing examines only observable amounts of liquid penetration, permeation may still occur. The use of penetration resistance data must be restricted to liquid chemicals, and should be limited to scenarios where there is no reasonable vapor exposure hazard under the conditions of exposure.

INTERPRETATION OF PERMEATION DATA

Permeation is the process of chemical movement through a material on a molecular level. Permeation resistance refers to the ability of a material to retard or prevent chemical movement through it. Permeation may occur without any visible signs of degradation.
Permeation resistance is measured using a test cell which is divided into two halves by a protective clothing specimen. Chemical is placed on the challenge side, while the collection side is periodically monitored for permeating chemical. Permeation data were obtained in accordance with the American Society for Testing and Materials (ASTM) Standard Test Method F 739 (Resistance of Materials Used in Protective Clothing to Permeation by Liquids and Gases), unless stated otherwise. In the case of chemicals that are classified as warfare agents, the data were obtained in accordance with the Military Standard 282 (MIL-STD-282) (Military Standard, Filter Units, Protective Clothing, Gas-Mask Components, and Related Products: Performance Test Methods).
Permeation rate is the amount of chemical that passes through a material for a measured surface area per unit time. In this section, permeation rate is expressed in micrograms per square centimeter per minute (mcg/cm(2)/min). The reported permeation rate is either the steady-state rate or the maximum rate observed during testing. In some cases, very large permeation rates exceed measurement techniques and are reported as ">" (greater than) or "HIGH."
Breakthrough time is the elapsed time, in minutes, from the time the chemical comes in contact with the material exterior surface, to the time that chemical is detected on the interior surface. When no breakthrough is detected, the breakthrough time is report as ">" the testing period. If permeation breakthrough is rapid, results are reported as "<" (less than) the earlier sampling time or as "IMMEDIATELY" (which usually means breakthrough in less than 4 minutes).
The breakthrough time should exceed the expected use period of the selected protective clothing. Additionally, there are several other factors that must be taken into account to provide appropriate protection.
Permeation testing is usually conducted with full strength, undiluted chemical for the duration of the test period. Actual exposures may involve diluted chemical for short or intermittent exposure periods.
Permeation testing is usually conducted at room temperature. Permeation occurs faster at elevated temperatures (short breakthrough times and higher permeation rates) and slower at reduced temperatures (long breakthrough times and lower permeation rates).
Permeation resistance of mixtures cannot usually be determined on the basis of the individual chemicals making up the mixture. Synergistic effects may occur and result in more rapid permeation than accounted for by the individual mixture chemicals.
Permeation rates may be used to calculate potential wearer exposure; however, several assumptions must be made about the extent of exposure and condition of clothing wear. Furthermore, there are few chemicals with dermal exposure limits, making it difficult to determine an acceptable skin exposure level.

COMPANY INFORMATION

ILC Dover, Inc. One Moonwalker Rd. Frederica, DE 19946-2080 USA Phone: (302) 335-3911 Toll-Free: (800) 631-9567 Website: http://www.ilcdover.com Email: Customer_Service@ilcdover.com

REFERENCES

CHEMICAL PROTECTIVE CLOTHING CITATIONS

The following sources were consulted for chemical protective clothing data:

(Ansell-Edmont, 2001)
(Bata Shoe Company, 1995)
(Best Manufacturing, 2002)
(Best Manufacturing, 2004)
(Boss Manufacturing Company, 1998)
(ChemFab Corporation, 1993)
(Comasec Safety, Inc., 2003)
(Comasec Safety, Inc., 2003a)
(DuPont, 2002)
(DuPont, 2002)
(DuPont, 2003)
(Guardian Manufacturing Group, 2001)
(ILC Dover, Inc., 1998)
(Kappler Inc., 2001)
(Kimberly-Clark, 2002)
(LaCrosse-Rainfair, 1997)
(MAPA Professional, 2003)
(MAPA Professional, 2004)
(Mar-Mac Manufacturing, Inc, 1995)
(Marigold Industrial, 2003)
(Memphis Glove Company, 2001)
(Montgomery Safety Products, 1995)
(Nat-Wear, 2001)
(Neese Industries, Inc., 2003)
(North, 2002)
(North, 2002)
(Playtex, 1995)
(River City, 1995)
(Safety 4, 2002)
(Servus, 1995)
(Standard Safety Equipment, 1995)
(Tingley, 2002)
(Trelleborg-Viking, Inc., 2001)
(Trelleborg-Viking, Inc., 2002)
(Wells Lamont Industrial, 2002)
(Workrite, 1997)

-PHYSICAL HAZARDS

FIRE HAZARD

SUMMARY

POTENTIAL FIRE OR EXPLOSION HAZARDS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)
- HIGHLY FLAMMABLE: Will be easily ignited by heat, sparks or flames.
- Vapors may form explosive mixtures with air.
- Vapors may travel to source of ignition and flash back.
- Most vapors are heavier than air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks).
- Vapor explosion hazard indoors, outdoors or in sewers.
- Those substances designated with a "P" may polymerize explosively when heated or involved in a fire.
- Runoff to sewer may create fire or explosion hazard.
- Containers may explode when heated.
- Many liquids are lighter than water.
Isopropyl ether is a very dangerous fire hazard and a severe explosion hazard when exposed to sparks, flames, heat, or oxidizing materials (Sax & Lewis, 1989).
Water spray can be used to protect personnel attempting to move containers or stop leaks (NFPA, 1986).
Containers that are exposed to the heat of a fire should be cooled from the side with flooding quantities of water until well after the fire is extinguished (NFPA, 1986; ITI, 1985; CHRIS , 1985).
NFPA HAZARD IDENTIFICATION: Health: 2; Flammability: 3; Reactivity: 1 (NFPA, 1986)

FLAMMABILITY CLASSIFICATION

NFPA Flammability Rating for CAS108-20-3 (NFPA, 2002):

Listed as: Isopropyl Ether
Flammability Rating: 3

(3) Flammable. Liquids and solids that can be ignited under almost all ambient temperature conditions. Including liquids with a flash point below 73 degrees F and a boiling point above 100 degrees F, solid materials which form coarse dusts that burn rapidly without becoming explosive, materials which burn rapidly by reason of self-contained oxygen (ie, organic peroxides), and materials which ignite spontaneously when exposed to air.

FIRE CONTROL/EXTINGUISHING AGENTS

FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

CAUTION: All these products have a very low flash point: Use of water spray when fighting fire may be inefficient.

SMALL FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Dry chemical, CO2, water spray or alcohol-resistant foam.

LARGE FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Water spray, fog or alcohol-resistant foam.
Use water spray or fog; do not use straight streams.
Move containers from fire area if you can do it without risk.

TANK OR CAR/TRAILER LOAD FIRE PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Fight fire from maximum distance or use unmanned hose holders or monitor nozzles.
Cool containers with flooding quantities of water until well after fire is out.
Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank.
ALWAYS stay away from tanks engulfed in fire.
For massive fire, use unmanned hose holders or monitor nozzles; if this is impossible, withdraw from area and let fire burn.

NFPA Extinguishing Methods for CAS108-20-3 (NFPA, 2002):

Listed as: Isopropyl Ether
Extinguishing Method(s): 5, 1

5: Flammable liquid fires can be extinguished using carbon dioxide, dry chemical, foam, and vaporizing liquid extinguishers, as long as the fires are small to moderate in size and the flammable liquid reservoir is shallow. Use of foam to form a blanket over a flammable liquid is not effective when the liquid is water-soluble. Certain alcohol resistant foams are effective extinguishing agents for polar, non-polar, and water-soluble liquid fires. These foams are preferred for fighting flammable liquid fires except those that involve water reactive flammable liquids.
1: "Water may be ineffective" applies to a situation where materials with a flash point below 100 degrees F (37.8 degrees C) are burning. Water will only be effective if used by experienced fire fighters under favorable conditions. Even though water may not put the fire out, it can be used to protect equipment and structures.

Fires may be fought with alcohol foam, carbon dioxide, foam, or dry chemical (Sax & Lewis, 1989; NFPA, 1986; ITI, 1985; CHRIS , 1985).

Water may be ineffective to extinguish fire (NFPA, 1986; ITI, 1985; CHRIS , 1985).

COMBUSTION TOXICITY

Isopropyl ether releases acrid smoke and fumes when heated to decomposition (Sax & Lewis, 1989).

EXPLOSION HAZARD

Isopropyl ether is a very dangerous fire hazard and a severe explosion hazard when exposed to sparks, flames, heat, or oxidizing materials (Sax & Lewis, 1989).

Shock may explode this material under certain conditions (Sax & Lewis, 1989).

Isopropyl ether tends to form peroxides more readily than does ethyl ether (Sax & Lewis, 1987).

Unstabilized isopropyl ether can readily form peroxides and may explode if shaken (Windholz et al, 1983).
Isopropyl ether forms very explosive and sensitive peroxides which precipitate in crystalline form on exposure to air (Sax & Lewis, 1989; ITI, 1985). Formed peroxides may also explode when heated (ITI, 1985).
Formed peroxides may be destroyed with a solution of sodium sulfite (Windholz et al, 1983).

DUST/VAPOR HAZARD

Isopropyl ether releases acrid smoke and fumes when heated to decomposition (Sax & Lewis, 1989).

REACTIVITY HAZARD

Isopropyl ether tends to form peroxides more readily than does ethyl ether (Sax & Lewis, 1987).

Unstabilized isopropyl ether can readily form peroxides and may explode if shaken (Windholz et al, 1983).
Isopropyl ether forms very explosive and sensitive peroxides which precipitate in crystalline form on exposure to air (Sax & Lewis, 1989; ITI, 1985). Formed peroxides may also explode when heated (ITI, 1985).
Formed peroxides may be destroyed with a solution of sodium sulfite (Windholz et al, 1983).

Isopropyl ether has potentially hazardous reactions with (Sax & Lewis, 1989):

Chlorosulfonic acid
Nitric acid
Propionyl chloride (dangerous reaction, may burst sealed containers)
Oxidizing materials

Isopropyl ether releases acrid smoke and fumes when heated to decomposition (Sax & Lewis, 1989).

Isopropyl ether is incompatible with strong oxidizing materials (Sittig, 1985; NIOSH , 1990).

Isopropyl ether does not react with water or common materials (CHRIS , 1985).

EVACUATION PROCEDURES

SUMMARY

Editor's Note: This material is not listed in the Table of Initial Isolation and Protective Action Distances.

LARGE SPILL - PUBLIC SAFETY EVACUATION DISTANCES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

Consider initial downwind evacuation for at least 300 meters (1000 feet).

FIRE - PUBLIC SAFETY EVACUATION DISTANCES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions.

PUBLIC SAFETY MEASURES - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)

CALL Emergency Response Telephone Number on Shipping Paper first. If Shipping Paper not available or no answer, refer to appropriate telephone number:

MEXICO:

SETIQ:

01-800-00-214-00 in the Mexican Republic;
For calls originating in Mexico City and the Metropolitan Area: 5559-1588;
For calls originating elsewhere, call: 011-52-555-559-1588.

CENACOM:

01-800-00-413-00 in the Mexican Republic;
For calls originating in Mexico City and the Metropolitan Area: 5550-1496, 5550-1552, 5550-1485, or 5550-4885;
For calls originating elsewhere, call: 011-52-555-550-1496, or 011-52-555-550-1552; 011-52-555-550-1485, or 011-52-555-550-4885.

ARGENTINA:

CIQUIME:

0-800-222-2933 in the Republic of Argentina;
For calls originating elsewhere, call: +54-11-4613-1100.

BRAZIL:

PRÓ-QUÍMICA:

0-800-118270 (Toll-free in Brazil);
For calls originating elsewhere, call: +55-11-232-1144 (Collect calls are accepted).

COLUMBIA:

CISPROQUIM:

01-800-091-6012 in Colombia;
For calls originating in Bogotá, Colombia, call: 288-6012;
For calls originating elsewhere, call: 011-57-1-288-6012.

CANADA:

CANUTEC:

613-996-6666 (Collect calls are accepted);
*666 cellular (in Canada only).

UNITED STATES:

CHEMTREC®:

1-800-424-9300 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
703-527-3887 for calls originating elsewhere (Collect calls are accepted).

CHEM-TEL, INC.:

1-800-255-3924 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
813-248-0585 for calls originating elsewhere (Collect calls are accepted).

INFOTRAC:

1-800-535-5053 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
352-323-3500 for calls originating elsewhere (Collect calls are accepted).

3E COMPANY:

1-800-451-8346 (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
760-602-8703 for calls originating elsewhere (Collect calls are accepted).

NATIONAL RESPONSE CENTER (NRC):

1-800-424-8802 - (24 hours) (Toll-free in the U.S., Canada, and the U.S. Virgin Islands);
202-267-2675 for calls in the District of Columbia.

MILITARY SHIPMENTS:

703-697-0218 - Explosives/ammunition incidents (Collect calls are accepted);
1-800-851-8061 - All other dangerous goods incidents.

NATIONWIDE POISON CONTROL CENTER (United States only):

1-800-222-1222 (Toll-free in the U.S.).

For additional details see the section entitled "WHO TO CALL FOR ASSISTANCE" under the ERG Instructions.
As an immediate precautionary measure, isolate spill or leak area for at least 50 meters (150 feet) in all directions.
Keep unauthorized personnel away.
Stay upwind.
Keep out of low areas.
Ventilate closed spaces before entering.

AIHA ERPG Values for CAS108-20-3 (AIHA, 2006):

Not Listed

DOE TEEL Values for CAS108-20-3 (U.S. Department of Energy, Office of Emergency Management, 2010):

Listed as Isopropyl ether; (Diisopropyl ether)
TEEL-0 (units = ppm): 250
TEEL-1 (units = ppm): 310
TEEL-2 (units = ppm): 310
TEEL-3 (units = ppm): 1400
Definitions:

TEEL-0: The threshold concentration below which most people will experience no adverse health effects.
TEEL-1: The airborne concentration (expressed as ppm [parts per million] or mg/m(3) [milligrams per cubic meter]) of a substance above which it is predicted that the general population, including susceptible individuals, could experience notable discomfort, irritation, or certain asymptomatic, nonsensory effects. However, these effects are not disabling and are transient and reversible upon cessation of exposure.
TEEL-2: The airborne concentration (expressed as ppm or mg/m(3)) of a substance above which it is predicted that the general population, including susceptible individuals, could experience irreversible or other serious, long-lasting, adverse health effects or an impaired ability to escape.
TEEL-3: The airborne concentration (expressed as ppm or mg/m(3)) of a substance above which it is predicted that the general population, including susceptible individuals, could experience life-threatening adverse health effects or death.

AEGL Values for CAS108-20-3 (National Research Council, 2010; National Research Council, 2009; National Research Council, 2008; National Research Council, 2007; NRC, 2001; NRC, 2002; NRC, 2003; NRC, 2004; NRC, 2004; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; United States Environmental Protection Agency Office of Pollution Prevention and Toxics, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2009; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2008; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2007; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2005; National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances, 2006; 62 FR 58840, 1997; 65 FR 14186, 2000; 65 FR 39264, 2000; 65 FR 77866, 2000; 66 FR 21940, 2001; 67 FR 7164, 2002; 68 FR 42710, 2003; 69 FR 54144, 2004):

Not Listed

NIOSH IDLH Values for CAS108-20-3 (National Institute for Occupational Safety and Health, 2007):

IDLH: 1400 ppm
Note(s): [10%LEL]

([10%LEL]) The 10%LEL designation is provided where the IDLH was based on 10% of the lower explosive limit. This is used for safety purposes in some cases even though toxicity is not indicative of irreversible health effects or impairment of escape exists only at higher concentrations.

CONTAINMENT/WASTE TREATMENT OPTIONS

SUMMARY

SPILL OR LEAK PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)
- ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area).
- All equipment used when handling the product must be grounded.
- Do not touch or walk through spilled material.
- Stop leak if you can do it without risk.
- Prevent entry into waterways, sewers, basements or confined areas.
- A vapor suppressing foam may be used to reduce vapors.
- Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers.
- Use clean non-sparking tools to collect absorbed material.
RECOMMENDED PROTECTIVE CLOTHING - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)
- Wear positive pressure self-contained breathing apparatus (SCBA).
- Structural firefighters' protective clothing will only provide limited protection.
Water spray can be used to dilute vapors prior to ignition and to flush spilled material away from sources of ignition (NFPA, 1986).

SMALL LEAK/SPILL

Small amounts of spilled liquid material can be absorbed with paper (ITI, 1985). After complete evaporation of the material, the paper can be disposed of by burning (ITI, 1985).

LARGE LEAK/SPILL

LARGE SPILL PRECAUTIONS - EMERGENCY RESPONSE GUIDEBOOK, GUIDE 127 (ERG, 2004)
- Dike far ahead of liquid spill for later disposal.
- Water spray may reduce vapor; but may not prevent ignition in closed spaces.
SUGGESTED DISPOSAL METHODS (Sittig, 1985; ITI, 1985)
- Concentrated waste which contains no peroxides can be incinerated by being discharged at a controlled rate near a pilot flame.
- Concentrated waste that contains peroxides should be disposed of by first perforating the waste container from a safe distance, followed by open burning.
- Open burning of material for disposal can be done, but the material should either first be evaporated or be ignited from a safe distance.
- Material for disposal can be dissolved in a combustible solvent such as benzene, petroleum ether, or a higher alcohol (ie, butanol) and then be burned.

-ENVIRONMENTAL HAZARD MANAGEMENT

POLLUTION HAZARD

Isopropyl ether's production and use as an extraction agent and as a solvent in paint and stain remover may result in environmental release through miscellaneous waste streams (HSDB, 2003).

ABIOTIC DEGRADATION

No information found at the time of this review.

ENVIRONMENTAL TOXICITY

The effect of low concentrations of isopropyl ether on aquatic life is not known, but the material may be dangerous if it enters water intakes (CHRIS , 1985).

Notify local health and wildlife authorities as well as operators of water intakes in the vicinity of water spills (CHRIS , 1985).

-PHYSICAL/CHEMICAL PROPERTIES

MOLECULAR WEIGHT

102.20 (RTECS , 1988)

DESCRIPTION/PHYSICAL STATE

Isopropyl ether is a colorless, volatile, flammable liquid with a sharp, sweetish, ether-like odor (Sax & Lewis, 1987; Sax & Lewis, 1989) ACGIH, 1986).

Isopropyl ether is available as the technical grade material (Sax & Lewis, 1987). It is shipped as a 94 percent or purer material, and may contain 0.01 percent of hydroquinone or another inhibitor to prevent peroxide formation (CHRIS , 1985).

VAPOR PRESSURE

150 mmHg (at 25 degrees C) (Sax & Lewis, 1989)

119 mmHg (at 20 degrees C) (ACGIH, 1986; (NIOSH , 1990)

SPECIFIC GRAVITY

OTHER TEMPERATURE AND/OR PRESSURE

0.7258 (at 20/4 degrees C) (Windholz et al, 1983)
0.723 (at 15.5/4 degrees C) (Sax & Lewis, 1987)

TEMPERATURE AND/OR PRESSURE NOT LISTED

0.7 (NFPA, 1986)

DENSITY

NORMAL TEMPERATURE AND PRESSURE

(25 degrees C; 77 degrees F and 760 mmHg)
0.719 g/mL (at 25 degrees C) (Sax & Lewis, 1989)

OTHER TEMPERATURE AND/OR PRESSURE

LIQUID: 0.724 g/mL (at 20 degrees C) (CHRIS , 1985)
0.7258 g/mL (at 20 degrees C) (ACGIH, 1986)

FREEZING/MELTING POINT

FREEZING POINT

-60 degrees C (Sax & Lewis, 1987)

MELTING POINT

-60 degrees C (Windholz et al, 1983) ACGIH, 1986)

BOILING POINT

67.5 degrees C (Sax & Lewis, 1987)

68-69 degrees C (Windholz et al, 1983) ACGIH, 1986; (NFPA, 1986)

FLASH POINT

-17.7 degrees C; 0 degrees F (Sax & Lewis, 1987)

9 degrees C; 5 degrees F (open cup) (Windholz et al, 1983) ACGIH, 1986)

-27.78 degrees C; -18 degrees F (closed cup) (ACGIH, 1986; (NFPA, 1986)

AUTOIGNITION TEMPERATURE

443 degrees C; 830 degrees F (Sax & Lewis, 1987; NFPA, 1986)

EXPLOSIVE LIMITS

LOWER

1.4% (NIOSH , 1990; Sax & Lewis, 1989; NFPA, 1986; CHRIS , 1985; ITI, 1985)

UPPER

21% (Sax & Lewis, 1987)
7.9% (NIOSH , 1990; Sax & Lewis, 1989; NFPA, 1986; CHRIS , 1985; ITI, 1985)

SOLUBILITY

IN WATER

Isopropyl ether is slightly soluble in water at 0.65% (by weight) (at 25 degrees C) and 0.2% (at 20 degrees C) (Sax & Lewis, 1987; Windholz et al, 1983; NFPA, 1986).

IN ORGANIC SOLVENTS

Isopropyl ether is soluble in most organic solvents (Sax & Lewis, 1987).
Isopropyl ether is miscible in ether or alcohol (Windholz et al, 1983) ACGIH, 1986).

-REFERENCES

GENERAL BIBLIOGRAPHY

40 CFR 372.28: Environmental Protection Agency - Toxic Chemical Release Reporting, Community Right-To-Know, Lower thresholds for chemicals of special concern. National Archives and Records Administration (NARA) and the Government Printing Office (GPO). Washington, DC. Final rules current as of Apr 3, 2006.

40 CFR 372.65: Environmental Protection Agency - Toxic Chemical Release Reporting, Community Right-To-Know, Chemicals and Chemical Categories to which this part applies. National Archives and Records Association (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Apr 3, 2006.

49 CFR 172.101 - App. B: Department of Transportation - Table of Hazardous Materials, Appendix B: List of Marine Pollutants. National Archives and Records Administration (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Aug 29, 2005.

49 CFR 172.101: Department of Transportation - Table of Hazardous Materials. National Archives and Records Administration (NARA) and the Government Printing Office (GPO), Washington, DC. Final rules current as of Aug 11, 2005.

62 FR 58840: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 1997.

65 FR 14186: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

65 FR 39264: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

65 FR 77866: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2000.

66 FR 21940: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2001.

67 FR 7164: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2002.

68 FR 42710: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2003.

69 FR 54144: Notice of the National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances - Proposed AEGL Values, Environmental Protection Agency, NAC/AEGL Committee. National Archives and Records Administration (NARA) and the Government Publishing Office (GPO), Washington, DC, 2004.

AIHA: 2006 Emergency Response Planning Guidelines and Workplace Environmental Exposure Level Guides Handbook, American Industrial Hygiene Association, Fairfax, VA, 2006.

American Conference of Governmental Industrial Hygienists : ACGIH 2010 Threshold Limit Values (TLVs(R)) for Chemical Substances and Physical Agents and Biological Exposure Indices (BEIs(R)), American Conference of Governmental Industrial Hygienists, Cincinnati, OH, 2010.

Ansell-Edmont: SpecWare Chemical Application and Recommendation Guide. Ansell-Edmont. Coshocton, OH. 2001. Available from URL: http://www.ansellpro.com/specware. As accessed 10/31/2001.

Bata Shoe Company: Industrial Footwear Catalog, Bata Shoe Company, Belcamp, MD, 1995.

Best Manufacturing: ChemRest Chemical Resistance Guide. Best Manufacturing. Menlo, GA. 2002. Available from URL: http://www.chemrest.com. As accessed 10/8/2002.

Best Manufacturing: Degradation and Permeation Data. Best Manufacturing. Menlo, GA. 2004. Available from URL: http://www.chemrest.com/DomesticPrep2/. As accessed 04/09/2004.

Boss Manufacturing Company: Work Gloves, Boss Manufacturing Company, Kewanee, IL, 1998.

Burgess JL, Kirk M, Borron SW, et al: Emergency department hazardous materials protocol for contaminated patients. Ann Emerg Med 1999; 34(2):205-212.

CHRIS : CHRIS Hazardous Chemical Data. US Department of Transportation, US Coast Guard. Washington, DC (Internet Version). Edition expires 1985; provided by Truven Health Analytics Inc., Greenwood Village, CO.

ChemFab Corporation: Chemical Permeation Guide Challenge Protective Clothing Fabrics, ChemFab Corporation, Merrimack, NH, 1993.

Comasec Safety, Inc.: Chemical Resistance to Permeation Chart. Comasec Safety, Inc.. Enfield, CT. 2003. Available from URL: http://www.comasec.com/webcomasec/english/catalogue/mtabgb.html. As accessed 4/28/2003.

Comasec Safety, Inc.: Product Literature, Comasec Safety, Inc., Enfield, CT, 2003a.

DFG: List of MAK and BAT Values 2002, Report No. 38, Deutsche Forschungsgemeinschaft, Commission for the Investigation of Health Hazards of Chemical Compounds in the Work Area, Wiley-VCH, Weinheim, Federal Republic of Germany, 2002.

DuPont: DuPont Suit Smart: Interactive Tool for the Selection of Protective Apparel. DuPont. Wilmington, DE. 2002. Available from URL: http://personalprotection.dupont.com/protectiveapparel/suitsmart/smartsuit2/na_english.asp. As accessed 10/31/2002.

DuPont: Permeation Guide for DuPont Tychem Protective Fabrics. DuPont. Wilmington, DE. 2003. Available from URL: http://personalprotection.dupont.com/en/pdf/tyvektychem/pgcomplete20030128.pdf. As accessed 4/26/2004.

DuPont: Permeation Test Results. DuPont. Wilmington, DE. 2002a. Available from URL: http://www.tyvekprotectiveapprl.com/databases/default.htm. As accessed 7/31/2002.

EPA: Search results for Toxic Substances Control Act (TSCA) Inventory Chemicals. US Environmental Protection Agency, Substance Registry System, U.S. EPA's Office of Pollution Prevention and Toxics. Washington, DC. 2005. Available from URL: http://www.epa.gov/srs/.

ERG: Emergency Response Guidebook. A Guidebook for First Responders During the Initial Phase of a Dangerous Goods/Hazardous Materials Incident, U.S. Department of Transportation, Research and Special Programs Administration, Washington, DC, 2004.

Guardian Manufacturing Group: Guardian Gloves Test Results. Guardian Manufacturing Group. Willard, OH. 2001. Available from URL: http://www.guardian-mfg.com/guardianmfg.html. As accessed 12/11/2001.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: 1,3-Butadiene, Ethylene Oxide and Vinyl Halides (Vinyl Fluoride, Vinyl Chloride and Vinyl Bromide), 97, International Agency for Research on Cancer, Lyon, France, 2008.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Formaldehyde, 2-Butoxyethanol and 1-tert-Butoxypropan-2-ol, 88, International Agency for Research on Cancer, Lyon, France, 2006.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Household Use of Solid Fuels and High-temperature Frying, 95, International Agency for Research on Cancer, Lyon, France, 2010a.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Smokeless Tobacco and Some Tobacco-specific N-Nitrosamines, 89, International Agency for Research on Cancer, Lyon, France, 2007.

IARC Working Group on the Evaluation of Carcinogenic Risks to Humans : IARC Monographs on the Evaluation of Carcinogenic Risks to Humans: Some Non-heterocyclic Polycyclic Aromatic Hydrocarbons and Some Related Exposures, 92, International Agency for Research on Cancer, Lyon, France, 2010.

IARC: List of all agents, mixtures and exposures evaluated to date - IARC Monographs: Overall Evaluations of Carcinogenicity to Humans, Volumes 1-88, 1972-PRESENT. World Health Organization, International Agency for Research on Cancer. Lyon, FranceAvailable from URL: http://monographs.iarc.fr/monoeval/crthall.html. As accessed Oct 07, 2004.

ICAO: Technical Instructions for the Safe Transport of Dangerous Goods by Air, 2003-2004. International Civil Aviation Organization, Montreal, Quebec, Canada, 2002.

ILC Dover, Inc.: Chemical Compatibility Chart. ILC Dover, Inc.. Frederica, DE. 1998a. Available from URL: http://www.ilcdover.com/WebDocs/chart.pdf; http://www.ilcdover.com/Products/ProtSuits/Ready1/chart.htm. As accessed 12/15/2001.

ILC Dover, Inc.: Ready 1 The Chemturion Limited Use Chemical Protective Suit, ILC Dover, Inc., Frederica, DE, 1998.

ITI: Toxic and Hazardous Industrial Chemicals Safety Manual, The International Technical Information Institute, Tokyo, Japan, 1985, pp 184-185.

International Agency for Research on Cancer (IARC): IARC monographs on the evaluation of carcinogenic risks to humans: list of classifications, volumes 1-116. International Agency for Research on Cancer (IARC). Lyon, France. 2016. Available from URL: http://monographs.iarc.fr/ENG/Classification/latest_classif.php. As accessed 2016-08-24.

International Agency for Research on Cancer: IARC Monographs on the Evaluation of Carcinogenic Risks to Humans. World Health Organization. Geneva, Switzerland. 2015. Available from URL: http://monographs.iarc.fr/ENG/Classification/. As accessed 2015-08-06.

Kappler, Inc.: Suit Smart. Kappler, Inc.. Guntersville, AL. 2001. Available from URL: http://www.kappler.com/suitsmart/smartsuit2/na_english.asp?select=1. As accessed 7/10/2001.

Kimberly-Clark, Inc.: Chemical Test Results. Kimberly-Clark, Inc.. Atlanta, GA. 2002. Available from URL: http://www.kc-safety.com/tech_cres.html. As accessed 10/4/2002.

LaCrosse-Rainfair: Safety Products, LaCrosse-Rainfair, Racine, WI, 1997.

MAPA Professional: Chemical Resistance Guide. MAPA North America. Columbia, TN. 2003. Available from URL: http://www.mapaglove.com/pro/ChemicalSearch.asp. As accessed 4/21/2003.

MAPA Professional: Chemical Resistance Guide. MAPA North America. Columbia, TN. 2004. Available from URL: http://www.mapaglove.com/ProductSearch.cfm?id=1. As accessed 6/10/2004.

Mar-Mac Manufacturing, Inc: Product Literature, Protective Apparel, Mar-Mac Manufacturing, Inc., McBee, SC, 1995.

Marigold Industrial: US Chemical Resistance Chart, on-line version. Marigold Industrial. Norcross, GA. 2003. Available from URL: www.marigoldindustrial.com/charts/uschart/uschart.html. As accessed 4/14/2003.

Memphis Glove Company: Permeation Guide. Memphis Glove Company. Memphis, TN. 2001. Available from URL: http://www.memphisglove.com/permeation.html. As accessed 7/2/2001.

Montgomery Safety Products: Montgomery Safety Products Chemical Resistant Glove Guide, Montgomery Safety Products, Canton, OH, 1995.

NFPA: Fire Protection Guide on Hazardous Materials, 9th ed, National Fire Protection Association, Boston, MA, 1986, pp 325M.

NFPA: Fire Protection Guide to Hazardous Materials, 13th ed., National Fire Protection Association, Quincy, MA, 2002.

NIOSH : Pocket Guide to Chemical Hazards. National Institute for Occupational Safety and Health. Cincinnati, OH. 1990.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 1, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2001.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 2, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2002.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 3, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2003.

NRC: Acute Exposure Guideline Levels for Selected Airborne Chemicals - Volume 4, Subcommittee on Acute Exposure Guideline Levels, Committee on Toxicology, Board on Environmental Studies and Toxicology, Commission of Life Sciences, National Research Council. National Academy Press, Washington, DC, 2004.

Nat-Wear: Protective Clothing, Hazards Chart. Nat-Wear. Miora, NY. 2001. Available from URL: http://www.natwear.com/hazchart1.htm. As accessed 7/12/2001.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2,3-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2,4-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2-Butylene Oxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648083cdbb&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,2-Dibromoethane (Proposed). United States Environmental Protection Agency. Washington, DC. 2007g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064802796db&disposition=attachment&contentType=pdf. As accessed 2010-08-18.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 1,3,5-Trimethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d68a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for 2-Ethylhexyl Chloroformate (Proposed). United States Environmental Protection Agency. Washington, DC. 2007b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648037904e&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Acrylonitrile (Proposed). United States Environmental Protection Agency. Washington, DC. 2007c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648028e6a3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Adamsite (Proposed). United States Environmental Protection Agency. Washington, DC. 2007h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Agent BZ (3-quinuclidinyl benzilate) (Proposed). United States Environmental Protection Agency. Washington, DC. 2007f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ad507&disposition=attachment&contentType=pdf. As accessed 2010-08-18.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Allyl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648039d9ee&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Aluminum Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Arsenic Trioxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2007m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480220305&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Automotive Gasoline Unleaded (Proposed). United States Environmental Protection Agency. Washington, DC. 2009a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cc17&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Biphenyl (Proposed). United States Environmental Protection Agency. Washington, DC. 2005j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064801ea1b7&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bis-Chloromethyl Ether (BCME) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006n. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648022db11&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Boron Tribromide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ae1d3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bromine Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2007d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648039732a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Bromoacetone (Proposed). United States Environmental Protection Agency. Washington, DC. 2008e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809187bf&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Calcium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Carbonyl Fluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803ae328&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Carbonyl Sulfide (Proposed). United States Environmental Protection Agency. Washington, DC. 2007e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648037ff26&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Chlorobenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2008c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064803a52bb&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Cyanogen (Proposed). United States Environmental Protection Agency. Washington, DC. 2008f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809187fe&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Dimethyl Phosphite (Proposed). United States Environmental Protection Agency. Washington, DC. 2009. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbf3&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Diphenylchloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648091884e&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyl Phosphorodichloridate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480920347&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethylbenzene (Proposed). United States Environmental Protection Agency. Washington, DC. 2008g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809203e7&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ethyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Germane (Proposed). United States Environmental Protection Agency. Washington, DC. 2008j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963906&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Hexafluoropropylene (Proposed). United States Environmental Protection Agency. Washington, DC. 2006. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064801ea1f5&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Ketene (Proposed). United States Environmental Protection Agency. Washington, DC. 2007. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ee7c&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Magnesium Aluminum Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Magnesium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Malathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2009k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064809639df&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Mercury Vapor (Proposed). United States Environmental Protection Agency. Washington, DC. 2009b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a8a087&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl Isothiocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963a03&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl Parathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2008l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963a57&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyl tertiary-butyl ether (Proposed). United States Environmental Protection Agency. Washington, DC. 2007a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064802a4985&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methylchlorosilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2005. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5f4&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Methyldichlorosilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2005a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c646&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN1 CAS Reg. No. 538-07-8) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006a. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN2 CAS Reg. No. 51-75-2) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006b. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Mustard (HN3 CAS Reg. No. 555-77-1) (Proposed). United States Environmental Protection Agency. Washington, DC. 2006c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6cb&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Tetroxide (Proposed). United States Environmental Protection Agency. Washington, DC. 2008n. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648091855b&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Nitrogen Trifluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009l. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963e0c&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Parathion (Proposed). United States Environmental Protection Agency. Washington, DC. 2008o. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480963e32&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Perchloryl Fluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e268&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Perfluoroisobutylene (Proposed). United States Environmental Protection Agency. Washington, DC. 2009d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e26a&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008p. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096dd58&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyl Mercaptan (Proposed). United States Environmental Protection Agency. Washington, DC. 2006d. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020cc0c&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phenyldichloroarsine (Proposed). United States Environmental Protection Agency. Washington, DC. 2007k. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020fd29&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phorate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008q. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096dcc8&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phosgene (Draft-Revised). United States Environmental Protection Agency. Washington, DC. 2009e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a8a08a&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Phosgene Oxime (Proposed). United States Environmental Protection Agency. Washington, DC. 2009f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e26d&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Potassium Cyanide (Proposed). United States Environmental Protection Agency. Washington, DC. 2009g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbb9&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Potassium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005c. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Propargyl Alcohol (Proposed). United States Environmental Protection Agency. Washington, DC. 2006e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec91&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Selenium Hexafluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2006f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec55&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Silane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006g. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d523&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sodium Cyanide (Proposed). United States Environmental Protection Agency. Washington, DC. 2009h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7cbb9&disposition=attachment&contentType=pdf. As accessed 2010-08-15.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sodium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Strontium Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005f. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Sulfuryl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2006h. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020ec7a&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tear Gas (Proposed). United States Environmental Protection Agency. Washington, DC. 2008s. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e551&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tellurium Hexafluoride (Proposed). United States Environmental Protection Agency. Washington, DC. 2009i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7e2a1&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tert-Octyl Mercaptan (Proposed). United States Environmental Protection Agency. Washington, DC. 2008r. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e5c7&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Tetramethoxysilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d632&disposition=attachment&contentType=pdf. As accessed 2010-08-17.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethoxysilane (Proposed). United States Environmental Protection Agency. Washington, DC. 2006i. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d632&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethyl Phosphite (Proposed). United States Environmental Protection Agency. Washington, DC. 2009j. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=0900006480a7d608&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Trimethylacetyl Chloride (Proposed). United States Environmental Protection Agency. Washington, DC. 2008t. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648096e5cc&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for Zinc Phosphide (Proposed). United States Environmental Protection Agency. Washington, DC. 2005e. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020c5ed&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

National Advisory Committee for Acute Exposure Guideline Levels for Hazardous Substances: Acute Exposure Guideline Levels (AEGLs) for n-Butyl Isocyanate (Proposed). United States Environmental Protection Agency. Washington, DC. 2008m. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=09000064808f9591&disposition=attachment&contentType=pdf. As accessed 2010-08-12.

National Institute for Occupational Safety and Health: NIOSH Pocket Guide to Chemical Hazards, U.S. Department of Health and Human Services, Centers for Disease Control and Prevention, Cincinnati, OH, 2007.

National Research Council : Acute exposure guideline levels for selected airborne chemicals, 5, National Academies Press, Washington, DC, 2007.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 6, National Academies Press, Washington, DC, 2008.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 7, National Academies Press, Washington, DC, 2009.

National Research Council: Acute exposure guideline levels for selected airborne chemicals, 8, National Academies Press, Washington, DC, 2010.

Neese Industries, Inc.: Fabric Properties Rating Chart. Neese Industries, Inc.. Gonzales, LA. 2003. Available from URL: http://www.neeseind.com/new/TechGroup.asp?Group=Fabric+Properties&Family=Technical. As accessed 4/15/2003.

North: Chemical Resistance Comparison Chart - Protective Footwear . North Safety. Cranston, RI. 2002. Available from URL: http://www.linkpath.com/index2gisufrm.php?t=N-USA1. As accessed April 30, 2004.

North: eZ Guide Interactive Software. North Safety. Cranston, RI. 2002a. Available from URL: http://www.northsafety.com/feature1.htm. As accessed 8/31/2002.

Playtex: Fits Tough Jobs Like a Glove, Playtex, Westport, CT, 1995.

Proctor NH & Hughes JP: Chemical Hazards of the Workplace, JB Lippincott Co, Philadelphia, PA, 1978, pp 304-305.

RTECS : Registry of Toxic Effects of Chemical Substances. National Institute for Occupational Safety and Health. Cincinnati, OH (Internet Version). Edition expires 1988; provided by Truven Health Analytics Inc., Greenwood Village, CO.

River City: Protective Wear Product Literature, River City, Memphis, TN, 1995.

Safety 4: North Safety Products: Chemical Protection Guide. North Safety. Cranston, RI. 2002. Available from URL: http://www.safety4.com/guide/set_guide.htm. As accessed 8/14/2002.

Sax NI & Lewis RJ: Dangerous Properties of Industrial Materials, 7th ed, Van Nostrand Reinhold Co, New York, NY, 1989, pp 1314.

Sax NI & Lewis RJ: Hawley's Condensed Chemical Dictionary, Van Nostrand Reinhold Co, New York, NY, 1987, pp 662.

Servus: Norcross Safety Products, Servus Rubber, Servus, Rock Island, IL, 1995.

Sittig M: Handbook of Toxic and Hazardous Chemicals and Carcinogens, 2nd ed, Noyes Publications, Park Ridge, NJ, 1985, pp 356.

Standard Safety Equipment: Product Literature, Standard Safety Equipment, McHenry, IL, 1995.

Tingley: Chemical Degradation for Footwear and Clothing. Tingley. South Plainfield, NJ. 2002. Available from URL: http://www.tingleyrubber.com/tingley/Guide_ChemDeg.pdf. As accessed 10/16/2002.

Trelleborg-Viking, Inc.: Chemical and Biological Tests (database). Trelleborg-Viking, Inc.. Portsmouth, NH. 2002. Available from URL: http://www.trelleborg.com/protective/. As accessed 10/18/2002.

Trelleborg-Viking, Inc.: Trellchem Chemical Protective Suits, Interactive manual & Chemical Database. Trelleborg-Viking, Inc.. Portsmouth, NH. 2001.

U.S. Department of Energy, Office of Emergency Management: Protective Action Criteria (PAC) with AEGLs, ERPGs, & TEELs: Rev. 26 for chemicals of concern. U.S. Department of Energy, Office of Emergency Management. Washington, DC. 2010. Available from URL: http://www.hss.doe.gov/HealthSafety/WSHP/Chem_Safety/teel.html. As accessed 2011-06-27.

U.S. Department of Health and Human Services, Public Health Service, National Toxicology Project : 11th Report on Carcinogens. U.S. Department of Health and Human Services, Public Health Service, National Toxicology Program. Washington, DC. 2005. Available from URL: http://ntp.niehs.nih.gov/INDEXA5E1.HTM?objectid=32BA9724-F1F6-975E-7FCE50709CB4C932. As accessed 2011-06-27.

U.S. Environmental Protection Agency: Discarded commercial chemical products, off-specification species, container residues, and spill residues thereof. Environmental Protection Agency's (EPA) Resource Conservation and Recovery Act (RCRA); List of hazardous substances and reportable quantities 2010b; 40CFR(261.33, e-f):77-.

U.S. Environmental Protection Agency: Integrated Risk Information System (IRIS). U.S. Environmental Protection Agency. Washington, DC. 2011. Available from URL: http://cfpub.epa.gov/ncea/iris/index.cfm?fuseaction=iris.showSubstanceList&list_type=date. As accessed 2011-06-21.

U.S. Environmental Protection Agency: List of Radionuclides. U.S. Environmental Protection Agency. Washington, DC. 2010a. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-sec302-4.pdf. As accessed 2011-06-17.

U.S. Environmental Protection Agency: List of hazardous substances and reportable quantities. U.S. Environmental Protection Agency. Washington, DC. 2010. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-sec302-4.pdf. As accessed 2011-06-17.

U.S. Environmental Protection Agency: The list of extremely hazardous substances and their threshold planning quantities (CAS Number Order). U.S. Environmental Protection Agency. Washington, DC. 2010c. Available from URL: http://www.gpo.gov/fdsys/pkg/CFR-2010-title40-vol27/pdf/CFR-2010-title40-vol27-part355.pdf. As accessed 2011-06-17.

U.S. Occupational Safety and Health Administration: Part 1910 - Occupational safety and health standards (continued) Occupational Safety, and Health Administration's (OSHA) list of highly hazardous chemicals, toxics and reactives. Subpart Z - toxic and hazardous substances. CFR 2010 2010; Vol6(SEC1910):7-.

U.S. Occupational Safety, and Health Administration (OSHA): Process safety management of highly hazardous chemicals. 29 CFR 2010 2010; 29(1910.119):348-.

United States Environmental Protection Agency Office of Pollution Prevention and Toxics: Acute Exposure Guideline Levels (AEGLs) for Vinyl Acetate (Proposed). United States Environmental Protection Agency. Washington, DC. 2006. Available from URL: http://www.regulations.gov/search/Regs/contentStreamer?objectId=090000648020d6af&disposition=attachment&contentType=pdf. As accessed 2010-08-16.

Wells Lamont Industrial: Chemical Resistant Glove Application Chart. Wells Lamont Industrial. Morton Grove, IL. 2002. Available from URL: http://www.wellslamontindustry.com. As accessed 10/31/2002.

Windholz M, Budavari S, & Blumetti RF: The Merck Index, 10th ed, Merck & Co, Inc, Rahway, NJ, 1983, pp 749.

Workrite: Chemical Splash Protection Garments, Technical Data and Application Guide, W.L. Gore Material Chemical Resistance Guide, Workrite, Oxnard, CA, 1997.

FeedBack

ISOPROPYL ETHER

Classification | Information to evaluate chemical incidents

Information to evaluate chemical incidents

Information to evaluate chemical incidents

Information to evaluate chemical incidents